On Thu, Nov 28, 2024 at 04:44:46PM +0800, Jingyi Wang wrote:
> Add initial support for Qualcomm QCS8300 RIDE board which enables DSPs,
> UFS and booting to shell with uart console.
>
> Written with help from Tingguo Cheng (added rpmhpd nodes) and Xin Liu
> (added ufs, adsp and gpdsp nodes).
>
> Reviewed-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> Signed-off-by: Jingyi Wang <quic_jingyw@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 2 +-
> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 267 ++++++++++++++++++++++++++++++
> 2 files changed, 268 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 9bb8b191aeb5..d9545743606a 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -114,7 +114,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> -dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> new file mode 100644
> index 000000000000..7eed19a694c3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> @@ -0,0 +1,267 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "qcs8300.dtsi"
> +/ {
> + model = "Qualcomm Technologies, Inc. QCS8300 Ride";
> + compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
> + chassis-type = "embedded";
> +
> + aliases {
> + serial0 = &uart7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + clocks {
> + xo_board_clk: xo-board-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <38400000>;
> + };
> +
> + sleep_clk: sleep-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32000>;
> + };
Move both clocks to the qcs8300.dtsi. If you wish, you can keep
frequencies in the board DT file.
> + };
> +};
> +
> +&apps_rsc {
> + regulators-0 {
> + compatible = "qcom,pmm8654au-rpmh-regulators";
> + qcom,pmic-id = "a";
> +
> + vreg_s4a: smps4 {
> + regulator-name = "vreg_s4a";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s9a: smps9 {
> + regulator-name = "vreg_s9a";
> + regulator-min-microvolt = <1352000>;
> + regulator-max-microvolt = <1352000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3a: ldo3 {
> + regulator-name = "vreg_l3a";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4a: ldo4 {
> + regulator-name = "vreg_l4a";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5a: ldo5 {
> + regulator-name = "vreg_l5a";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6a: ldo6 {
> + regulator-name = "vreg_l6a";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a: ldo7 {
> + regulator-name = "vreg_l7a";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8a: ldo8 {
> + regulator-name = "vreg_l8a";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9a: ldo9 {
> + regulator-name = "vreg_l9a";
> + regulator-min-microvolt = <2970000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pmm8654au-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vreg_s5c: smps5 {
> + regulator-name = "vreg_s5c";
> + regulator-min-microvolt = <1104000>;
> + regulator-max-microvolt = <1104000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1c: ldo1 {
> + regulator-name = "vreg_l1c";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <500000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2c: ldo2 {
> + regulator-name = "vreg_l2c";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <904000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4c: ldo4 {
> + regulator-name = "vreg_l4c";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6c: ldo6 {
> + regulator-name = "vreg_l6c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7c: ldo7 {
> + regulator-name = "vreg_l7c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8c: ldo8 {
> + regulator-name = "vreg_l8c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9c: ldo9 {
> + regulator-name = "vreg_l9c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&gcc {
> + clocks = <&rpmhcc RPMH_CXO_CLK>,
> + <&sleep_clk>,
> + <0>,
> + <0>,
> + <0>,
> + <0>,
> + <0>,
> + <0>,
> + <0>,
> + <0>;
Move this to the qcs8300.dtsi (and rpmhcc too).
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/qcs8300/adsp.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> + firmware-name = "qcom/qcs8300/cdsp0.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_gpdsp {
> + firmware-name = "qcom/qcs8300/gpdsp0.mbn";
> + status = "okay";
> +};
> +
> +&rpmhcc {
> + clocks = <&xo_board_clk>;
> + clock-names = "xo";
qcs8300.dtsi
> +};
> +
> +&uart7 {
> + status = "okay";
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
> + vcc-supply = <&vreg_l8a>;
> + vcc-max-microamp = <1100000>;
> + vccq-supply = <&vreg_l4c>;
> + vccq-max-microamp = <1200000>;
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l4a>;
> + vdda-pll-supply = <&vreg_l5a>;
> + status = "okay";
> +};
>
> --
> 2.25.1
>
--
With best wishes
Dmitry
