On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote:
> From: Jishnu Prakash <quic_jprakash@xxxxxxxxxxx>
>
> Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750
> platforms.
Up/lower case?
>
> Signed-off-by: Jishnu Prakash <quic_jprakash@xxxxxxxxxxx>
> Signed-off-by: Melody Olvera <quic_molvera@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++
Those two are independent changes. Please use two separate patches.
> 2 files changed, 118 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
> new file mode 100644
> index 000000000000..f8ef8e133854
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
> @@ -0,0 +1,56 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> + thermal-zones {
> + pmd8028-thermal {
> + polling-delay-passive = <100>;
> + thermal-sensors = <&pmd8028_temp_alarm>;
> +
> + trips {
> + pmd8028_trip0: trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + pmd8028_trip1: trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
"critical" ?
> + };
> + };
> + };
> + };
> +};
> +
> +&spmi_bus {
> + pmd8028: pmic@4 {
> + compatible = "qcom,pmd8028", "qcom,spmi-pmic";
> + reg = <0x4 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmd8028_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pmd8028_gpios: gpio@8800 {
> + compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmd8028_gpios 0 0 4>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
> new file mode 100644
> index 000000000000..3907d8fbcf78
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
> @@ -0,0 +1,62 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> + thermal-zones {
> + pmih0108-thermal {
> + polling-delay-passive = <100>;
> + thermal-sensors = <&pmih0108_temp_alarm>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
"critical" ?
> + };
> + };
> + };
> + };
> +};
> +
> +&spmi_bus {
> + pmih0108: pmic@7 {
> + compatible = "qcom,pmih0108", "qcom,spmi-pmic";
> + reg = <0x7 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmih0108_temp_alarm: temp-alarm@a00 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0xa00>;
> + interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pmih0108_gpios: gpio@8800 {
> + compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio";
> + reg = <0x8800>;
> + gpio-controller;
> + gpio-ranges = <&pmih0108_gpios 0 0 18>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + pmih0108_eusb2_repeater: phy@fd00 {
> + compatible = "qcom,pm8550b-eusb2-repeater";
> + reg = <0xfd00>;
> + #phy-cells = <0>;
> + };
> + };
> +};
> --
> 2.46.1
>
--
With best wishes
Dmitry
