Hi, 2016-06-26 20:20 GMT+09:00 Chanwoo Choi <cwchoi00@xxxxxxxxx>: > Hi, > > This patch looks good to me. > But, there is some comment. > > 2016-06-26 14:56 GMT+09:00 Stephen Boyd <stephen.boyd@xxxxxxxxxx>: >> Some Qualcomm PMICs have a misc device that performs USB id pin >> detection via an interrupt. When the interrupt triggers, we >> should read the interrupt line to see if it has gone high or low. >> If the interrupt is low then the ID pin is grounded, and if the >> interrupt is high then the ID pin is being held high. >> >> Cc: Roger Quadros <rogerq@xxxxxx> >> Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx> >> Signed-off-by: Stephen Boyd <stephen.boyd@xxxxxxxxxx> >> --- >> .../bindings/extcon/qcom,pm8941-misc.txt | 41 +++++ >> drivers/extcon/Kconfig | 6 + >> drivers/extcon/Makefile | 1 + >> drivers/extcon/extcon-qcom-spmi-misc.c | 170 +++++++++++++++++++++ >> 4 files changed, 218 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt >> create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c >> >> diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt >> new file mode 100644 >> index 000000000000..35383adb10f1 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt >> @@ -0,0 +1,41 @@ >> +Qualcomm's PM8941 USB ID Extcon device >> + >> +Some Qualcomm PMICs have a "misc" module that can be used to detect when >> +the USB ID pin has been pulled low or high. >> + >> +PROPERTIES >> + >> +- compatible: >> + Usage: required >> + Value type: <string> >> + Definition: Should contain "qcom,pm8941-misc"; >> + >> +- reg: >> + Usage: required >> + Value type: <u32> >> + Definition: Should contain the offset to the misc address space > > 'reg' property is used on extcon-qcom-spmi-misc.c? > I think that you don't need to include this property. > >> + >> +- interrupts: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: Should contain the usb id interrupt >> + >> +- interrupt-names: >> + Usage: required >> + Value type: <stringlist> >> + Definition: Should contain the string "usb_id" for the usb id interrupt >> + >> +Example: >> + >> + pmic { >> + usb_id: misc@900 { >> + compatible = "qcom,pm8941-misc"; >> + reg = <0x900>; >> + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; >> + interrupt-names = "usb_id"; >> + }; >> + } >> + >> + usb-controller { >> + extcon = <&usb_id>; >> + }; >> diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig >> index 3d89e60a3e71..b2ee47cb10ca 100644 >> --- a/drivers/extcon/Kconfig >> +++ b/drivers/extcon/Kconfig >> @@ -119,6 +119,12 @@ config EXTCON_SM5502 >> Silicon Mitus SM5502. The SM5502 is a USB port accessory >> detector and switch. >> >> +config EXTCON_QCOM_SPMI_MISC >> + tristate "Qualcomm USB extcon support" >> + help >> + Say Y here to enable SPMI PMIC based USB cable detection >> + support on Qualcomm PMICs such as PM8941. > > You need to reorder the entry alphabetically. You better to move > it below Sorry. Before completing the reply, I send the email. You better to move the entry on below EXTCON_PALMAS. > >> + >> config EXTCON_USB_GPIO >> tristate "USB GPIO extcon support" >> depends on GPIOLIB || COMPILE_TEST >> diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile >> index 2a0e4f45d5b2..8cf6eb068d34 100644 >> --- a/drivers/extcon/Makefile >> +++ b/drivers/extcon/Makefile >> @@ -15,4 +15,5 @@ obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o >> obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o >> obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o >> obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o >> +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o ditto. Thanks, Chanwoo Choi [snip] -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html