On Thursday 23 June 2016 11:55:46 Matthew McClintock wrote:
> What is the command line? What is the FDT load address from u-boot?
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00072
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 1679 - bootable_media_detect_success, Start
B - 1692 - elf_loader_entry, Start
B - 5068 - auth_hash_seg_entry, Start
B - 7212 - auth_hash_seg_exit, Start
B - 568520 - elf_segs_hash_verify_entry, Start
B - 682592 - PBL, End
B - 682616 - SBL1, Start
B - 772516 - pm_device_init, Start
D - 6 - pm_device_init, Delta
B - 773957 - boot_flash_init, Start
D - 52725 - boot_flash_init, Delta
B - 830856 - boot_config_data_table_init, Start
D - 3805 - boot_config_data_table_init, Delta - (419 Bytes)
B - 838058 - clock_init, Start
D - 7583 - clock_init, Delta
B - 850162 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:2,Subtype:0
B - 853653 - sbl1_ddr_set_params, Start
B - 858644 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 863030 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13154 - sbl1_ddr_set_params, Delta
B - 876854 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 883505 - sbl1_wait_for_ddr_training, Start
D - 31 - sbl1_wait_for_ddr_training, Delta
B - 902916 - Image Load, Start
D - 138201 - QSEE Image Loaded, Delta - (267732 Bytes)
B - 1041617 - Image Load, Start
D - 1448 - SEC Image Loaded, Delta - (2048 Bytes)
B - 1051836 - Image Load, Start
D - 173993 - APPSBL Image Loaded, Delta - (353891 Bytes)
B - 1226254 - QSEE Execution, Start
D - 66 - QSEE Execution, Delta
B - 1232440 - SBL1, End
D - 551938 - SBL1, Delta
S - Flash Throughput, 1991 KB/s (624090 Bytes, 313384 us)
S - DDR Fre�
U-Boot 2012.07 [Barrier Breaker r40864,r40864] (Feb 16 2016 - 23:33:08)
smem ram ptable found: ver: 1 len: 3
DRAM: 128 MiB
WARNING: Caches not enabled
machid : 0x8010200
NAND: SF: Detected Spansion with page size 64 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x2000000
32 MiB
MMC:
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
machid: 8010200
Net:
OM3 standard: change gpio 59 -> 63
MAC0 addr:0:3:7f:ba:db:ad
ipq40xx_ess_sw_init done
PHY ID1: 0x4d
PHY ID2: 0xd0b2
eth0
Hit any key to stop autoboot: 0
(IPQ40xx) #
(IPQ40xx) #
(IPQ40xx) # setenv serverip 192.168.2.227
(IPQ40xx) # setenv ipaddr 192.168.2.3
(IPQ40xx) # setenv bootargs loglevel=8 earlyprintk console=ttyS0,115200
(IPQ40xx) # tftpboot 0x81000000 lede-ipq806x-APDK01-initramfs-fit-uImage.itb
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 up Speed :1000 Full duplex
Using eth0 device
TFTP from server 192.168.2.227; our IP address is 192.168.2.3
Filename 'lede-ipq806x-APDK01-initramfs-fit-uImage.itb'.
Load address: 0x81000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################################
done
Bytes transferred = 6347916 (60dc8c hex)
(IPQ40xx) # bootm 0x81000000
## Booting kernel from FIT Image at 81000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.7-rc3
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x810000e4
Data Size: 6340562 Bytes = 6 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: d12421ed
Hash algo: sha1
Hash value: b25692f363b076c63134e3d452316117002c3c85
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 81000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt APDK01 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8160c1e8
Data Size: 6014 Bytes = 5.9 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 337abac9
Hash algo: sha1
Hash value: 8193d932fb65464c0f12822f777aa220638a9e0f
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8160c1e8
Uncompressing Kernel Image ... OK
Loading Device Tree to 8722b000, end 8722f77d ... OK
ipq: fdt fixup unable to find compatible node
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010200 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.7.0-rc3 (sven@bentobox) (gcc version 5.3.0 (LEDE GCC 5.3.0 r611) ) #4 SMP PREEMPT Thu Jun 23 15:38:04 UTC 2016
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writeallocAttachment:
signature.asc
Description: This is a digitally signed message part.
