Remove the power-domain property from the DSI, HDMI and eDP dt-binding
docs. The power domain only needs to be specified in the parent MDSS
device node (that too only for SoCs which contain MDSS).
Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/display/msm/dsi.txt | 3 ---
Documentation/devicetree/bindings/display/msm/edp.txt | 2 --
Documentation/devicetree/bindings/display/msm/hdmi.txt | 4 ----
3 files changed, 9 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
index e6933a8..c1ef181 100644
--- a/Documentation/devicetree/bindings/display/msm/dsi.txt
+++ b/Documentation/devicetree/bindings/display/msm/dsi.txt
@@ -8,7 +8,6 @@ Required properties:
- reg-names: The names of register regions. The following regions are required:
* "dsi_ctrl"
- interrupts: The interrupt signal from the DSI block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: Phandles to device clocks.
- clock-names: the following clocks are required:
* "mdp_core_clk"
@@ -94,7 +93,6 @@ Required properties:
* "dsi_phy_regulator"
- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
2 clocks: A byte clock (index 0), and a pixel clock (index 1).
-- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: Phandles to device clocks. See [1] for details on clock bindings.
- clock-names: the following clocks are required:
* "iface_clk"
@@ -116,7 +114,6 @@ Example:
interrupts = <4 0>;
reg-names = "dsi_ctrl";
reg = <0xfd922800 0x200>;
- power-domains = <&mmcc MDSS_GDSC>;
clock-names =
"bus_clk",
"byte_clk",
diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt
index 3a20f6e..e712dfa 100644
--- a/Documentation/devicetree/bindings/display/msm/edp.txt
+++ b/Documentation/devicetree/bindings/display/msm/edp.txt
@@ -8,7 +8,6 @@ Required properties:
* "edp"
* "pll_base"
- interrupts: The interrupt signal from the eDP block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
- clock-names: the following clocks are required:
@@ -39,7 +38,6 @@ Example:
<0xfd923a00 0xd4>;
interrupt-parent = <&mdss_mdp>;
interrupts = <12 0>;
- power-domains = <&mmcc MDSS_GDSC>;
clock-names =
"core_clk",
"pixel_clk",
diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt
index b63f614..ce84459 100644
--- a/Documentation/devicetree/bindings/display/msm/hdmi.txt
+++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt
@@ -11,7 +11,6 @@ Required properties:
- reg: Physical base address and length of the controller's registers
- reg-names: "core_physical"
- interrupts: The interrupt signal from the hdmi block.
-- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See ../clocks/clock-bindings.txt for details.
- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
@@ -48,7 +47,6 @@ Required properties:
* "hdmi_tx_l1"
* "hdmi_tx_l3"
* "hdmi_tx_l4"
-- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
- core-vdda-supply: phandle to vdda regulator device node
@@ -63,7 +61,6 @@ Example:
reg-names = "core_physical";
reg = <0x04a00000 0x2f0>;
interrupts = <GIC_SPI 79 0>;
- power-domains = <&mmcc MDSS_GDSC>;
clock-names =
"core_clk",
"master_iface_clk",
@@ -92,7 +89,6 @@ Example:
reg = <0x4a00400 0x60>,
<0x4a00500 0x100>;
#phy-cells = <0>;
- power-domains = <&mmcc MDSS_GDSC>;
clock-names = "slave_iface_clk";
clocks = <&mmcc HDMI_S_AHB_CLK>;
core-vdda-supply = <&pm8921_hdmi_mvs>;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
