On Fri, Oct 18, 2024 at 2:49 PM Bartosz Golaszewski <brgl@xxxxxxxx> wrote: > > This series previously only concerned sc8280xp but while enabling > WLAN/BT on sm8450 I noticed some more changes will be required so I > folded the latter into this series and updated the sc8280xp CRD and X13 > patches. > > == > > This models the WLAN and Bluetooth modules on several boards using the > WCN6855 module. > > The wcn6855 (also known as qca6490) is a bit different from the qca6390 > so modify the power sequencing driver to support it with separate device > match data. > > For the sc8280xp-crd and sm8450-hdk we add the PMU, wifi and bluetooth > nodes with the correctly modelled wiring between them. For the X13s, we > rework existing nodes so that they align with the new DT bindings > contract. > > On sm8450-hdk we require some additional toggling of the XO-CLK signal > so add that to the driver as well and update the bindings. > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> > --- > Changes in v6: > - add the xo-clk signal handling to the pwrseq-qcom-wcn driver > - add a patch enabling wifi and bluetooth on sm8450-hdk > - add missing supplies to the PMUs on sc8280xp boards > - Link to v5: https://lore.kernel.org/all/20241008102545.40003-1-brgl@xxxxxxxx/ > > Changes in v5: > - put vreg_s10b under the "B" PMIC on the CRD instead of modeling it as a > fixed regulator > - order pinctrl nodes alphabetically > - restore the drive-strength property for all pins to what bootfw sets it to > - disable bias on wlan-en pin on the CRD > - remove stray newline > - add the swctrl pins to the PMU node > > Changes in v4: > - bind bluetooth pins on X13s in patch 3/3 > - only drop the regulator-always-on properties for vreg_s11b and vreg_s12b > and fold this change into patch 3/3 > > Changes in v3: > - move adding the bt-enable-gpios to the PMU on the CRD to patch 2/4 > - add a patch removing the regulator-always-on property from regulators > on X13s that no longer need it > > Changes in v2: > - fix commit message in patch 1/3 > - drop drive-strength from the wlan enable pin function > - drop the calibration variant property from the wifi node of the CRD > > --- > Bartosz Golaszewski (6): > regulator: dt-bindings: qcom,qca6390-pmu: add more properties for wcn6855 > power: sequencing: qcom-wcn: improve support for wcn6855 > arm64: dts: qcom: sc8280xp-crd: model the PMU of the on-board wcn6855 > arm64: dts: qcom: sc8280xp-crd: enable bluetooth > arm64: dts: qcom: sc8280xp-x13s: model the PMU of the on-board wcn6855 > arm64: dts: qcom: sm8450-hdk: model the PMU of the on-board wcn6855 > > .../bindings/regulator/qcom,qca6390-pmu.yaml | 12 ++ > arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 169 +++++++++++++++++++++ > .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 103 +++++++++++-- > arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 157 +++++++++++++++++++ > arch/arm64/boot/dts/qcom/sm8450.dtsi | 2 +- > drivers/power/sequencing/pwrseq-qcom-wcn.c | 101 +++++++++++- > 6 files changed, 526 insertions(+), 18 deletions(-) > --- > base-commit: f2493655d2d3d5c6958ed996b043c821c23ae8d3 > change-id: 20240807-sc8280xp-pwrseq-7b6859d846c5 > > Best regards, > -- > Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> > It's been two weeks. If there are no objections to the DTS changes, can the remainder of this series be picked up for v6.13? Thanks, Bartosz
