Hi Marc,
There are two ways you could enable MI2S audio via HDMI,
1. via ADSP, which is what you have in the DT.
2. by passing DSP directly configuring to LPASS MI2S registers.(this
needs a speical tz firmware to allow cpu to access LPASS registers)
You need to do only one thing, not the both.
By looking at some of the errors i would suggest you to
1. check if the MI2S pins are correctly configured.
2. if MCLK and BITCLK for these are MI2S are configured correctly with
the required clk rate. (Pl take a look at existing examples sdm845/8016...)
3. set the correct mixers to connect FE and BE dai links.(look at
existing ucm files for hints)
thanks,
Srini
On 10/10/2024 17:10, Marc Gonzalez wrote:
On 08/10/2024 17:49, Marc Gonzalez wrote:
On 08/10/2024 15:46, Marc Gonzalez wrote:
[ 15.106412] qcom,apr 17300000.remoteproc:glink-edge.apr_audio_svc.-1.-1: Adding APR/GPR dev: aprsvc:apr-service:4:3
[ 15.109935] qcom,apr 17300000.remoteproc:glink-edge.apr_audio_svc.-1.-1: Adding APR/GPR dev: aprsvc:apr-service:4:4
[ 15.119041] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_probe:1759
[ 15.134672] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: q6afe_dai_dev_probe
[ 15.137948] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: of_q6afe_parse_dai_data
[ 15.146461] qcom,apr 17300000.remoteproc:glink-edge.apr_audio_svc.-1.-1: Adding APR/GPR dev: aprsvc:apr-service:4:7
[ 15.153563] remoteproc remoteproc0: powering up 4080000.remoteproc
[ 15.166371] remoteproc remoteproc0: Booting fw image mba.mbn, size 234152
[ 15.169747] q6asm-dai 17300000.remoteproc:glink-edge:apr:apr-service@7:dais: Adding to iommu group 5
[ 15.170559] qcom,apr 17300000.remoteproc:glink-edge.apr_audio_svc.-1.-1: Adding APR/GPR dev: aprsvc:apr-service:4:8
[ 15.179732] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: msm_dai_q6_dai_probe
[ 15.199345] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_find_port:860
[ 15.208834] msm-snd-msm8998 sound: ASoC: registered pcm #0 MultiMedia1 (*)
[ 15.216194] msm-snd-msm8998 sound: snd-soc-dummy-dai <-> MultiMedia1 mapping ok
[ 15.221994] msm-snd-msm8998 sound: ASoC: registered pcm #1 MultiMedia2 (*)
[ 15.229582] msm-snd-msm8998 sound: snd-soc-dummy-dai <-> MultiMedia2 mapping ok
[ 15.236045] msm-snd-msm8998 sound: ASoC: registered pcm #2 (HDMI)
[ 15.243211] msm-snd-msm8998 sound: i2s-hifi <-> HDMI mapping ok
[ 15.285770] input: batfish Headset Jack as /devices/platform/sound/sound/card0/input2
[ 15.298010] qcom-q6v5-mss 4080000.remoteproc: MBA booted without debug policy, loading mpss
[ 15.542937] remoteproc remoteproc0: remote processor 4080000.remoteproc is now up
If I try to play sound on the HDMI link:
# tinymix set "HDMI Mixer MultiMedia1" 1
(no logs on the command line or in dmesg)
# tinyplay /home/equinox.wav
playing '/home/equinox.wav': 2 ch, 48000 hz, 16 bit
error playing sample
The corresponding kernel logs are:
[ 204.324095] msm-snd-msm8998 sound: ASoC: find BE for widget MultiMedia1 Playback
[ 204.324280] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.330832] msm-snd-msm8998 sound: ASoC: try BE : I2S Playback
[ 204.336452] msm-snd-msm8998 sound: ASoC: find BE for widget MM_DL1
[ 204.342361] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.348471] msm-snd-msm8998 sound: ASoC: try BE : I2S Playback
[ 204.354319] msm-snd-msm8998 sound: ASoC: find BE for widget HDMI Mixer
[ 204.360152] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.366702] msm-snd-msm8998 sound: ASoC: try BE : I2S Playback
[ 204.372545] msm-snd-msm8998 sound: ASoC: find BE for widget HDMI_RX
[ 204.378439] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.384520] msm-snd-msm8998 sound: ASoC: try BE : I2S Playback
[ 204.390471] msm-snd-msm8998 sound: ASoC: find BE for widget HDMI Playback
[ 204.396400] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.403231] MultiMedia1: ASoC: found 2 audio Playback paths
[ 204.408912] MultiMedia1: YO: dpcm_add_paths:1595
[ 204.414855] MultiMedia1: YO: dpcm_add_paths:1601
[ 204.419435] MultiMedia1: YO: dpcm_add_paths:1605 widget=MM_DL1
[ 204.424105] MultiMedia1: YO: dpcm_add_paths:1605 widget=HDMI Mixer
[ 204.429867] MultiMedia1: YO: dpcm_add_paths:1605 widget=HDMI_RX
[ 204.436139] MultiMedia1: YO: dpcm_add_paths:1605 widget=HDMI Playback
[ 204.442394] msm-snd-msm8998 sound: ASoC: find BE for widget HDMI Playback
[ 204.448691] msm-snd-msm8998 sound: ASoC: try BE : HDMI Playback
[ 204.455581] MultiMedia1: YO: dpcm_add_paths:1638
[ 204.461316] MultiMedia1: connected new DPCM Playback path MultiMedia1 -> HDMI
[ 204.466220] MultiMedia1: ASoC: found 1 new BE paths
[ 204.473232] HDMI: ASoC: open Playback BE HDMI
[ 204.478379] MultiMedia1: ASoC: open FE MultiMedia1
[ 204.482911] HDMI: ASoC: hw_params BE HDMI
[ 204.487489] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: q6hdmi_hw_params
[ 204.491715] MultiMedia1: ASoC: hw_params FE MultiMedia1 rate 48000 chan 2 fmt 2
[ 204.500814] MultiMedia1: ASoC: prepare FE MultiMedia1
[ 204.508108] HDMI: ASoC: prepare BE HDMI
[ 204.512978] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: q6afe_dai_prepare
[ 204.517117] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_hdmi_port_prepare:1317
[ 204.525864] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_port_start:1511
[ 204.533151] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_port_set_param_v2:1050
[ 204.540129] qcom-q6afe aprsvc:apr-service:4:4: YO: afe_apr_send_pkt:947
[ 204.547820] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_callback:880
[ 204.553692] qcom-q6afe aprsvc:apr-service:4:4: cmd = 0x100ef returned error = 0x18
[ 204.560292] qcom-q6afe aprsvc:apr-service:4:4: YO: q6afe_find_port:860
[ 204.567937] qcom-q6afe aprsvc:apr-service:4:4: DSP returned error[18]
[ 204.574262] qcom-q6afe aprsvc:apr-service:4:4: AFE enable for port 0x100e failed -22
[ 204.583561] qcom-q6afe aprsvc:apr-service:4:4: AFE enable for port 0x100e failed -22
[ 204.591317] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: fail to start AFE port 1
[ 204.599101] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: ASoC: error at snd_soc_pcm_dai_prepare on HDMI: -22
[ 204.608501] MultiMedia1: ASoC: hw_free FE MultiMedia1
[ 204.619781] HDMI: ASoC: hw_free BE HDMI
[ 204.624821] q6afe-dai 17300000.remoteproc:glink-edge:apr:apr-service@4:dais: YOA: q6afe_dai_shutdown
[ 204.628835] MultiMedia1: ASoC: close FE MultiMedia1
[ 204.637798] HDMI: ASoC: BE HDMI event 2 dir 0
[ 204.642745] MultiMedia1: ASoC: BE Playback disconnect check for HDMI
[ 204.646987] MultiMedia1: freed DSP Playback path MultiMedia1 -> HDMI
Looks like the audio DSP might not be correctly initialized?
[ Adding Bjorn & Jeffrey & Rohit ]
Right now, I'm thinking I might (??) need the code in sound/soc/qcom/lpass-cpu.c
to be called.
$ git grep asoc_qcom_lpass_cpu_platform_probe
sound/soc/qcom/lpass-apq8016.c: .probe = asoc_qcom_lpass_cpu_platform_probe,
sound/soc/qcom/lpass-cpu.c:int asoc_qcom_lpass_cpu_platform_probe(struct platform_device *pdev)
sound/soc/qcom/lpass-cpu.c:EXPORT_SYMBOL_GPL(asoc_qcom_lpass_cpu_platform_probe);
sound/soc/qcom/lpass-ipq806x.c: .probe = asoc_qcom_lpass_cpu_platform_probe,
sound/soc/qcom/lpass-msm8998.c: .probe = asoc_qcom_lpass_cpu_platform_probe,
sound/soc/qcom/lpass-sc7180.c: .probe = asoc_qcom_lpass_cpu_platform_probe,
sound/soc/qcom/lpass-sc7280.c: .probe = asoc_qcom_lpass_cpu_platform_probe,
sound/soc/qcom/lpass.h:int asoc_qcom_lpass_cpu_platform_probe(struct platform_device *pdev);
For example, lpass-sc7280.c defines "qcom,sc7280-lpass-cpu"
Binding:
Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml
Corresponding DTS in arch/arm64/boot/dts/qcom/sc7280.dtsi
lpass_cpu: audio@3987000 {
compatible = "qcom,sc7280-lpass-cpu";
reg = <0 0x03987000 0 0x68000>,
<0 0x03b00000 0 0x29000>,
<0 0x03260000 0 0xc000>,
<0 0x03280000 0 0x29000>,
<0 0x03340000 0 0x29000>,
<0 0x0336c000 0 0x3000>;
reg-names = "lpass-hdmiif",
"lpass-lpaif",
"lpass-rxtx-cdc-dma-lpm",
"lpass-rxtx-lpaif",
"lpass-va-lpaif",
"lpass-va-cdc-dma-lpm";
iommus = <&apps_smmu 0x1820 0>,
<&apps_smmu 0x1821 0>,
<&apps_smmu 0x1832 0>;
power-domains = <&rpmhpd SC7280_LCX>;
power-domain-names = "lcx";
required-opps = <&rpmhpd_opp_nom>;
clocks = <&lpass_aon LPASS_AON_CC_AUDIO_HM_H_CLK>,
<&lpass_core LPASS_CORE_CC_EXT_MCLK0_CLK>,
<&lpass_core LPASS_CORE_CC_SYSNOC_MPORT_CORE_CLK>,
<&lpass_core LPASS_CORE_CC_EXT_IF0_IBIT_CLK>,
<&lpass_core LPASS_CORE_CC_EXT_IF1_IBIT_CLK>,
<&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM_CLK>,
<&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM0_CLK>,
<&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM1_CLK>,
<&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM2_CLK>,
<&lpass_aon LPASS_AON_CC_VA_MEM0_CLK>;
clock-names = "aon_cc_audio_hm_h",
"audio_cc_ext_mclk0",
"core_cc_sysnoc_mport_core",
"core_cc_ext_if0_ibit",
"core_cc_ext_if1_ibit",
"audio_cc_codec_mem",
"audio_cc_codec_mem0",
"audio_cc_codec_mem1",
"audio_cc_codec_mem2",
"aon_cc_va_mem0";
#sound-dai-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "lpass-irq-lpaif",
"lpass-irq-hdmi",
"lpass-irq-vaif",
"lpass-irq-rxtxif";
status = "disabled";
};
Is there an equivalent HW block for msm8998?
Vendor kernel has no hits for hdmiif.
I don't see anything relevant downstream :(
Do I need to look at the HW block at address 0xee000000 ?
lpass-lpaif could be LPASS_LPA_IF_REG_BASE at LPASS_BASE + 0x00100000 ?
Regards
