Re: [PATCH v2] arm64: dts: qcom: x1e80100: Switch PCIe 6a to 4 lanes mode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 24-10-06 22:57:05, Dmitry Baryshkov wrote:
> On Fri, Oct 04, 2024 at 12:06:33PM GMT, Abel Vesa wrote:
> > The PCIe 6a controller and PHY can be configured in 4-lanes mode or
> > 2-lanes mode. For 4-lanes mode, it fetches the lanes provided by PCIe 6b.
> > For 2-lanes mode, PCIe 6a uses 2 lanes and then PCIe 6b uses the other 2
> > lanes. Configure it in 4-lane mode and then each board can configure it
> > depending on the design. Both the QCP and CRD boards, currently upstream,
> > use PCIe 6a for NVMe in 4-lane mode. Mark the controller as 4-lane as
> > well. This is the last change needed in order to support NVMe with Gen4
> > 4-lanes on all existing X Elite boards.
> 
> What about other X1E80100 devices supported upstream? Do they also use
> this controller in 4 lane mode?

Yes, by my knowledge, all upstream boards with X1E80100 use this
controller for NVMe in 4 lanes mode.

There is a question about the Galaxy Book4 Edge, as I think that uses
UFS instead, and my guess is it doesn't use the PCIe 6a for anything.
But that is not yet merged.

> 
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
> > ---
> > Changes in v2:
> > - Re-worded the commit message according to Johan's suggestions
> > - Dropped the clocks changes.
> > - Dropped the fixes tag as this relies on the Gen4 4-lanes stability
> >   patchset which has been only merged in 6.12, so backporting this patch
> >   would break NVMe support for all platforms.
> > - Link to v1: https://lore.kernel.org/r/20240531-x1e80100-dts-fixes-pcie6a-v1-2-1573ebcae1e8@xxxxxxxxxx
> > ---
> >  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 9 ++++++---
> >  1 file changed, 6 insertions(+), 3 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > index a36076e3c56b5b8815eb41ec55e2e1e5bd878201..4ec712cb7a26d8fe434631cf15949524fd22c7d9 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > @@ -2931,7 +2931,7 @@ pcie6a: pci@1bf8000 {
> >  			dma-coherent;
> >  
> >  			linux,pci-domain = <6>;
> > -			num-lanes = <2>;
> > +			num-lanes = <4>;
> >  
> >  			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>,
> >  				     <GIC_SPI 774 IRQ_TYPE_LEVEL_HIGH>,
> > @@ -2997,8 +2997,9 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> >  		};
> >  
> >  		pcie6a_phy: phy@1bfc000 {
> > -			compatible = "qcom,x1e80100-qmp-gen4x2-pcie-phy";
> > -			reg = <0 0x01bfc000 0 0x2000>;
> > +			compatible = "qcom,x1e80100-qmp-gen4x4-pcie-phy";
> 
> Oh...

Yes, we default to 4 lanes here.

> 
> > +			reg = <0 0x01bfc000 0 0x2000>,
> > +			      <0 0x01bfe000 0 0x2000>;
> >  
> >  			clocks = <&gcc GCC_PCIE_6A_PHY_AUX_CLK>,
> >  				 <&gcc GCC_PCIE_6A_CFG_AHB_CLK>,
> > @@ -3021,6 +3022,8 @@ pcie6a_phy: phy@1bfc000 {
> >  
> >  			power-domains = <&gcc GCC_PCIE_6_PHY_GDSC>;
> >  
> > +			qcom,4ln-config-sel = <&tcsr 0x1a000 0>;
> > +
> >  			#clock-cells = <0>;
> >  			clock-output-names = "pcie6a_pipe_clk";
> >  
> > 
> > ---
> > base-commit: c02d24a5af66a9806922391493205a344749f2c4
> > change-id: 20241003-x1e80100-dts-fixes-pcie6a-b9f1171e8d5b
> > 
> > Best regards,
> > -- 
> > Abel Vesa <abel.vesa@xxxxxxxxxx>
> > 
> 
> -- 
> With best wishes
> Dmitry




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux