Re: [PATCH] arm64: dts: qcom: qcm6490: Allow UFS regulators load/mode setting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Oct 04, 2024 at 01:31:10PM GMT, Rakesh Kota wrote:
> The UFS driver expects to be able to set load (and by extension, mode)
> on its supply regulators. Add the necessary properties to make that
> possible.
> 
> While at it, UFS rails have different voltage requirement for UFS2.x
> v/s UFS3.x. Bootloader sets the proper voltage based on UFS type.
> There can be case where the voltage set by bootloader is overridden
> by HLOS client.
> 

It's generally not accepted to do "while at it"-changes, but it happens
that I accept it. This one however, is controversial. We tend to want to
properly describe the voltage constraints, so this departure from that
stance definitely isn't an acceptable "while at it"-change...

> To prevent above issue, add change to remove voltage voting support
> for dedicated UFS rails.

You state that the bootloader will configure the appropriate voltage, I
don't see a issue description.


Either way, please split this in two.

Regards,
Bjorn

> 
> Signed-off-by: Rakesh Kota <quic_kotarake@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 12 ++++++++----
>  1 file changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
> index 84c45419cb8d..8a4df9c2a946 100644
> --- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
> @@ -258,13 +258,15 @@ vreg_l6b_1p2: ldo6 {
>  			regulator-name = "vreg_l6b_1p2";
>  			regulator-min-microvolt = <1140000>;
>  			regulator-max-microvolt = <1260000>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM RPMH_REGULATOR_MODE_HPM>;
>  			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
>  		vreg_l7b_2p952: ldo7 {
>  			regulator-name = "vreg_l7b_2p952";
> -			regulator-min-microvolt = <2400000>;
> -			regulator-max-microvolt = <3544000>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM RPMH_REGULATOR_MODE_HPM>;
>  			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
> @@ -277,8 +279,8 @@ vreg_l8b_0p904: ldo8 {
>  
>  		vreg_l9b_1p2: ldo9 {
>  			regulator-name = "vreg_l9b_1p2";
> -			regulator-min-microvolt = <1200000>;
> -			regulator-max-microvolt = <1304000>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM RPMH_REGULATOR_MODE_HPM>;
>  			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
> @@ -467,6 +469,8 @@ vreg_l10c_0p88: ldo10 {
>  			regulator-name = "vreg_l10c_0p88";
>  			regulator-min-microvolt = <720000>;
>  			regulator-max-microvolt = <1050000>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM RPMH_REGULATOR_MODE_HPM>;
>  			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
> -- 
> 2.34.1
> 




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux