Hi, > Add support to get the device parameters from ACPI. Assume that the clocks > are managed by firmware. > > Signed-off-by: Naveen Kaje <nkaje@xxxxxxxxxxxxxx> > --- > drivers/i2c/busses/i2c-qup.c | 59 +++++++++++++++++++++++++++++++++--- > -------- > 1 file changed, 44 insertions(+), 15 deletions(-) > <.snip> > +/* Default values. Use these if FW query fails */ #define > +DEFAULT_CLK_FREQ 100000 #define DEFAULT_SRC_CLK 20000000 > + > struct qup_i2c_block { > int count; > int pos; > @@ -1360,8 +1365,8 @@ static int qup_i2c_probe(struct platform_device > *pdev) > struct resource *res; > u32 io_mode, hw_ver, size; > int ret, fs_div, hs_div; > - int src_clk_freq; > - u32 clk_freq = 100000; > + u32 src_clk_freq = 0; > + u32 clk_freq = 0; > int blocks; > > qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL); @@ - > 1372,7 +1377,12 @@ static int qup_i2c_probe(struct platform_device *pdev) > init_completion(&qup->xfer); > platform_set_drvdata(pdev, qup); > > - of_property_read_u32(node, "clock-frequency", &clk_freq); > + ret = device_property_read_u32(qup->dev, "clock-frequency", > &clk_freq); > + if (ret) { > + dev_warn(qup->dev, "using default clock-frequency %d", > + DEFAULT_CLK_FREQ); > + clk_freq = DEFAULT_CLK_FREQ; > + } > > if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup- > v1.1.1")) { > qup->adap.algo = &qup_i2c_algo; > @@ -1454,20 +1464,31 @@ nodma: > return qup->irq; > } > > - qup->clk = devm_clk_get(qup->dev, "core"); > - if (IS_ERR(qup->clk)) { > - dev_err(qup->dev, "Could not get core clock\n"); > - return PTR_ERR(qup->clk); > - } > + if (ACPI_HANDLE(qup->dev)) { > + ret = device_property_read_u32(qup->dev, > + "src-clock-hz", &src_clk_freq); > + if (ret) { > + dev_warn(qup->dev, "using default src-clock-hz %d", > + DEFAULT_SRC_CLK); > + src_clk_freq = DEFAULT_SRC_CLK; > + } > + ACPI_COMPANION_SET(&qup->adap.dev, > ACPI_COMPANION(qup->dev)); > + } else { > + qup->clk = devm_clk_get(qup->dev, "core"); > + if (IS_ERR(qup->clk)) { > + dev_err(qup->dev, "Could not get core clock\n"); > + return PTR_ERR(qup->clk); > + } > > - qup->pclk = devm_clk_get(qup->dev, "iface"); > - if (IS_ERR(qup->pclk)) { > - dev_err(qup->dev, "Could not get iface clock\n"); > - return PTR_ERR(qup->pclk); > + qup->pclk = devm_clk_get(qup->dev, "iface"); > + if (IS_ERR(qup->pclk)) { > + dev_err(qup->dev, "Could not get iface clock\n"); > + return PTR_ERR(qup->pclk); > + } > + qup_i2c_enable_clocks(qup); > + src_clk_freq = clk_get_rate(qup->clk); > } > > - qup_i2c_enable_clocks(qup); > - > /* > * Bootloaders might leave a pending interrupt on certain QUP's, > * so we reset the core before registering for interrupts. > @@ -1514,7 +1535,6 @@ nodma: > size = QUP_INPUT_FIFO_SIZE(io_mode); > qup->in_fifo_sz = qup->in_blk_sz * (2 << size); > > - src_clk_freq = clk_get_rate(qup->clk); > fs_div = ((src_clk_freq / clk_freq) / 2) - 3; > hs_div = 3; > qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); @@ -1639,6 +1659,14 > @@ static const struct of_device_id qup_i2c_dt_match[] = { }; > MODULE_DEVICE_TABLE(of, qup_i2c_dt_match); > > +#if IS_ENABLED(CONFIG_ACPI) > +static const struct acpi_device_id qup_i2c_acpi_match[] = { > + { "QCOM8010"}, > + { }, > +}; > +MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_ids); #endif > + > static struct platform_driver qup_i2c_driver = { > .probe = qup_i2c_probe, > .remove = qup_i2c_remove, > @@ -1646,6 +1674,7 @@ static struct platform_driver qup_i2c_driver = { > .name = "i2c_qup", > .pm = &qup_i2c_qup_pm_ops, > .of_match_table = qup_i2c_dt_match, > + .acpi_match_table = ACPI_PTR(qup_i2c_acpi_match), > }, > }; > Reviewed-by: sricharan@xxxxxxxxxxxxxx Regards, Sricharan -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html