Re: [PATCH] PCI: qcom-ep: Do not enable resources during probe()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 23, 2024 at 10:11:33AM +0530, Manivannan Sadhasivam wrote:
> On Thu, Aug 22, 2024 at 12:31:33PM -0500, Bjorn Helgaas wrote:
> > On Thu, Aug 22, 2024 at 09:10:25PM +0530, Manivannan Sadhasivam wrote:
> > > On Thu, Aug 22, 2024 at 10:16:58AM -0500, Bjorn Helgaas wrote:
> > > > On Thu, Aug 22, 2024 at 12:18:23PM +0530, Manivannan Sadhasivam wrote:
> > > > > On Wed, Aug 21, 2024 at 05:56:18PM -0500, Bjorn Helgaas wrote:
> > > > > ...
> > > > 
> > > > > > Although I do have the question of what happens if the RC deasserts
> > > > > > PERST# before qcom-ep is loaded.  We probably don't execute
> > > > > > qcom_pcie_perst_deassert() in that case, so how does the init happen?
> > > > > 
> > > > > PERST# is a level trigger signal. So even if the host has asserted
> > > > > it before EP booted, the level will stay low and ep will detect it
> > > > > while booting.
> > > > 
> > > > The PERST# signal itself is definitely level oriented.
> > > > 
> > > > I'm still skeptical about the *interrupt* from the PCIe controller
> > > > being level-triggered, as I mentioned here:
> > > > https://lore.kernel.org/r/20240815224735.GA57931@bhelgaas
> > > 
> > > Sorry, that comment got buried into my inbox. So didn't get a chance
> > > to respond.
> > > 
> > > > tegra194 is also dwc-based and has a similar PERST# interrupt but
> > > > it's edge-triggered (tegra_pcie_ep_pex_rst_irq()), which I think
> > > > is a cleaner implementation.  Then you don't have to remember the
> > > > current state, switch between high and low trigger, worry about
> > > > races and missing a pulse, etc.
> > > 
> > > I did try to mimic what tegra194 did when I wrote the qcom-ep
> > > driver, but it didn't work. If we use the level triggered interrupt
> > > as edge, the interrupt will be missed if we do not listen at the
> > > right time (when PERST# goes from high to low and vice versa).
> > > 
> > > I don't know how tegra194 interrupt controller is wired up, but IIUC
> > > they will need to boot the endpoint first and then host to catch the
> > > PERST# interrupt.  Otherwise, the endpoint will never see the
> > > interrupt until host toggles it again.
> > 
> > Having to control the boot ordering of endpoint and host is definitely
> > problematic.
> > 
> > What is the nature of the crash when we try to enable the PHY when
> > Refclk is not available?  The endpoint has no control over when the
> > host asserts/deasserts PERST#.  If PERST# happens to be asserted while
> > the endpoint is enabling the PHY, and this causes some kind of crash
> > that the endpoint driver can't easily recover from, that's a serious
> > robustness problem.
> 
> The whole endpoint SoC crashes if the refclk is not available during
> phy_power_on() as the PHY driver tries to access some register on Dmitry's
> platform (I did not see this crash on SM8450 SoC though).
> 
> If we keep the enable_resources() during probe() then the race condition you
> observed above could apply. So removing that from probe() will also make the
> race condition go away,

Example:

  1) host deasserts PERST#
  2) qcom-ep handles PERST# IRQ
  3) qcom_pcie_ep_perst_irq_thread() calls qcom_pcie_perst_deassert()
  4) host asserts PERST#, Refclk no longer valid
  5) qcom_pcie_perst_deassert() calls qcom_pcie_enable_resources()
  6) qcom_pcie_enable_resources() enables PHY

I don't see what prevents the PERST# assertion at 4.  It sounds like
the endpoint SoC crashes at 6.




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux