On 14/08/2024 00:00, Richard Acayan wrote:
The camera subsystem for the SDM670 the same as on SDM845 except with
3 CSIPHY ports instead of 4. Add support for the SDM670 camera
subsystem.
Signed-off-by: Richard Acayan <mailingradian@xxxxxxxxx>
---
drivers/media/platform/qcom/camss/camss.c | 194 ++++++++++++++++++++++
1 file changed, 194 insertions(+)
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 51b1d3550421..f5d8443d4157 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -584,6 +584,188 @@ static const struct camss_subdev_resources vfe_res_660[] = {
}
};
+static const struct camss_subdev_resources csiphy_res_670[] = {
+ /* CSIPHY0 */
+ {
+ .regulators = {},
+ .clock = { "camnoc_axi", "soc_ahb", "cpas_ahb",
+ "csiphy0", "csiphy0_timer" },
Per previous comment, you're specifying camnoc_axi here, so you can just
set it to whatever it was 80MHz I think.
You shouldn't need the Camera NoC clock to do an I2C/CCI transaction ...
nor TBH for the CSIPHY.
Should probably live in the CSID alone.
+ .clock_rate = { { 0 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 19200000, 240000000, 269333333 } },
+ .reg = { "csiphy0" },
+ .interrupt = { "csiphy0" },
+ .csiphy = {
+ .hw_ops = &csiphy_ops_3ph_1_0,
+ .formats = &csiphy_formats_sdm845
+ }
+ },
+
+ /* CSIPHY1 */
+ {
+ .regulators = {},
+ .clock = { "camnoc_axi", "soc_ahb", "cpas_ahb",
+ "csiphy1", "csiphy1_timer" },
+ .clock_rate = { { 0 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 19200000, 240000000, 269333333 } },
+ .reg = { "csiphy1" },
+ .interrupt = { "csiphy1" },
+ .csiphy = {
+ .hw_ops = &csiphy_ops_3ph_1_0,
+ .formats = &csiphy_formats_sdm845
+ }
+ },
+
+ /* CSIPHY2 */
+ {
+ .regulators = {},
+ .clock = { "camnoc_axi", "soc_ahb", "cpas_ahb",
+ "csiphy2", "csiphy2_timer" },
+ .clock_rate = { { 0 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 19200000, 240000000, 269333333 } },
+ .reg = { "csiphy2" },
+ .interrupt = { "csiphy2" },
+ .csiphy = {
+ .hw_ops = &csiphy_ops_3ph_1_0,
+ .formats = &csiphy_formats_sdm845
+ }
+ }
+};
+
+static const struct camss_subdev_resources csid_res_670[] = {
+ /* CSID0 */
+ {
+ .regulators = { "vdda-phy", "vdda-pll" },
+ .clock = { "cpas_ahb", "soc_ahb", "vfe0",
+ "vfe0_cphy_rx", "csi0" },
You don't need csiX clock in both VFE and CSID.
Should almost certainly only be in CSID.
+ .clock_rate = { { 0 },
+ { 0 },
+ { 100000000, 320000000, 404000000, 480000000, 600000000 },
+ { 384000000 },
+ { 19200000, 75000000, 384000000, 538666667 } },
+ .reg = { "csid0" },
+ .interrupt = { "csid0" },
+ .csid = {
+ .hw_ops = &csid_ops_gen2,
+ .formats = &csid_formats_gen2
+ }
+ },
+
+ /* CSID1 */
+ {
+ .regulators = { "vdda-phy", "vdda-pll" },
+ .clock = { "cpas_ahb", "soc_ahb", "vfe1",
+ "vfe1_cphy_rx", "csi1" },
+ .clock_rate = { { 0 },
+ { 0 },
+ { 100000000, 320000000, 404000000, 480000000, 600000000 },
+ { 384000000 },
+ { 19200000, 75000000, 384000000, 538666667 } },
+ .reg = { "csid1" },
+ .interrupt = { "csid1" },
+ .csid = {
+ .hw_ops = &csid_ops_gen2,
+ .formats = &csid_formats_gen2
+ }
+ },
+
+ /* CSID2 */
+ {
+ .regulators = { "vdda-phy", "vdda-pll" },
+ .clock = { "cpas_ahb", "soc_ahb", "vfe_lite",
+ "vfe_lite_cphy_rx", "csi2" },
+ .clock_rate = { { 0 },
+ { 0 },
+ { 100000000, 320000000, 404000000, 480000000, 600000000 },
+ { 384000000 },
+ { 19200000, 75000000, 384000000, 538666667 } },
+ .reg = { "csid2" },
+ .interrupt = { "csid2" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen2,
+ .formats = &csid_formats_gen2
+ }
+ }
+};
+
+static const struct camss_subdev_resources vfe_res_670[] = {
+ /* VFE0 */
+ {
+ .regulators = {},
+ .clock = { "camnoc_axi", "cpas_ahb", "soc_ahb",
+ "vfe0", "vfe0_axi", "csi0" },
Please try to zap that csi0 clock for your v3, only specifying it in CSID.
---
bod
