Re: [PATCH 3/4] arm64: dts: qcom: x1e80100: Add UART2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 09, 2024 at 03:43:22AM +0200, Konrad Dybcio wrote:
> From: Konrad Dybcio <quic_kdybcio@xxxxxxxxxxx>
> 
> GENI SE2 within QUP0 is used as UART on some devices, describe it.
> 
> Signed-off-by: Konrad Dybcio <quic_kdybcio@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 52 ++++++++++++++++++++++++++++++++++
>  1 file changed, 52 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index 326283822aee..a2a011702752 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -2142,6 +2142,28 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
>  				status = "disabled";
>  			};
>  
> +			uart2: serial@b88000 {
> +				compatible = "qcom,geni-uart";
> +				reg = <0 0x00b88000 0 0x4000>;
> +
> +				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
> +
> +				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> +				clock-names = "se";
> +
> +				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
> +						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
> +						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> +						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
> +				interconnect-names = "qup-core",
> +						     "qup-config";
> +
> +				pinctrl-0 = <&qup_uart2_default>;
> +				pinctrl-names = "default";
> +
> +				status = "disabled";
> +			};
> +
>  			spi2: spi@b88000 {
>  				compatible = "qcom,geni-spi";
>  				reg = <0 0x00b88000 0 0x4000>;
> @@ -5365,6 +5387,36 @@ qup_spi23_data_clk: qup-spi23-data-clk-state {
>  				bias-disable;
>  			};
>  
> +			qup_uart2_default: qup-uart2-default-state {
> +				cts-pins {
> +					pins = "gpio8";
> +					function = "qup0_se2";
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +
> +				rts-pins {
> +					pins = "gpio9";
> +					function = "qup0_se2";
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +
> +				tx-pins {
> +					pins = "gpio10";
> +					function = "qup0_se2";
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +
> +				rx-pins {
> +					pins = "gpio11";
> +					function = "qup0_se2";
> +					drive-strength = <2>;
> +					bias-disable;
> +				};

Can you combine these into a single entry, i.e.

				pins = "gpio8", "gpio9", "gpio10", "gpio11";

if they are all the same?

Thanks,
Stephan




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux