The common PLL controller provides clocks to networking hardware blocks on Qualcomm IPQ SoC. It receives input clock from the on-chip Wi-Fi, and produces output clocks at fixed rates. These output rates are predetermined, and are unrelated to the input clock rate. The output clocks are supplied to the Ethernet hardware such as PPE (packet process engine) and the externally connected switch or PHY device. The common PLL driver is initially being supported for IPQ9574 SoC. Signed-off-by: Luo Jie <quic_luoj@xxxxxxxxxxx> --- .../bindings/clock/qcom,ipq-cmn-pll.yaml | 87 ++++++++++++++++++++++ 1 file changed, 87 insertions(+) diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq-cmn-pll.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq-cmn-pll.yaml new file mode 100644 index 000000000000..c45b3a201751 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,ipq-cmn-pll.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,ipq-cmn-pll.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Common PLL Clock Controller on IPQ SoC + +maintainers: + - Bjorn Andersson <andersson@xxxxxxxxxx> + - Luo Jie <quic_luoj@xxxxxxxxxxx> + +description: + The common PLL clock controller expects a reference input clock. + This reference clock is from the on-board Wi-Fi. The CMN PLL + supplies a number of fixed rate output clocks to the Ethernet + devices including PPE (packet process engine) and the connected + switch or PHY device. + +properties: + compatible: + enum: + - qcom,ipq9574-cmn-pll + + reg: + maxItems: 1 + + clocks: + items: + - description: The reference clock, the supported clock rates include + 25000000, 31250000, 40000000, 48000000, 50000000 and 96000000 HZ. + - description: The AHB clock + - description: The SYS clock + description: + The reference clock is the source clock of CMN PLL, which is from the + Wi-Fi. The AHB and SYS clocks must be enabled to access common PLL + clock registers. + + clock-names: + items: + - const: ref + - const: ahb + - const: sys + + clock-output-names: + items: + - const: ppe-353mhz + - const: eth0-50mhz + - const: eth1-50mhz + - const: eth2-50mhz + - const: eth-25mhz + description: + The output clocks are given to Ethernet blocks that includes PPE and + the connected switch or PHY device. + + "#clock-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - clock-output-names + - "#clock-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,ipq9574-gcc.h> + + clock-controller@9b000 { + compatible = "qcom,ipq9574-cmn-pll"; + reg = <0x0009b000 0x800>; + clocks = <&cmn_pll_ref_clk>, + <&gcc GCC_CMN_12GPLL_AHB_CLK>, + <&gcc GCC_CMN_12GPLL_SYS_CLK>; + clock-names = "ref", "ahb", "sys"; + clock-output-names = "ppe-353mhz", + "eth0-50mhz", + "eth1-50mhz", + "eth2-50mhz", + "eth-25mhz"; + #clock-cells = <1>; + }; +... -- 2.34.1
