Remove the bindings for the Qualcomm 8x16 PHY driver that was dropped
in commit 4756f35fdf14 ("usb: phy: remove phy-qcom-8x16-usb.c") in 2017.
Signed-off-by: Rayyan Ansari <rayyan.ansari@xxxxxxxxxx>
---
.../bindings/phy/qcom,usb-8x16-phy.txt | 76 -------------------
1 file changed, 76 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt
deleted file mode 100644
index 2cb2168cef41..000000000000
--- a/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt
+++ /dev/null
@@ -1,76 +0,0 @@
-Qualcomm's APQ8016/MSM8916 USB transceiver controller
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: Should contain "qcom,usb-8x16-phy".
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: USB PHY base address and length of the register map
-
-- clocks:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: See clock-bindings.txt section "consumers". List of
- two clock specifiers for interface and core controller
- clocks.
-
-- clock-names:
- Usage: required
- Value type: <string>
- Definition: Must contain "iface" and "core" strings.
-
-- vddcx-supply:
- Usage: required
- Value type: <phandle>
- Definition: phandle to the regulator VDCCX supply node.
-
-- v1p8-supply:
- Usage: required
- Value type: <phandle>
- Definition: phandle to the regulator 1.8V supply node.
-
-- v3p3-supply:
- Usage: required
- Value type: <phandle>
- Definition: phandle to the regulator 3.3V supply node.
-
-- resets:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: See reset.txt section "consumers". PHY reset specifier.
-
-- reset-names:
- Usage: required
- Value type: <string>
- Definition: Must contain "phy" string.
-
-- switch-gpio:
- Usage: optional
- Value type: <prop-encoded-array>
- Definition: Some boards are using Dual SPDT USB Switch, witch is
- controlled by GPIO to de/multiplex D+/D- USB lines
- between connectors.
-
-Example:
- usb_phy: phy@78d9000 {
- compatible = "qcom,usb-8x16-phy";
- reg = <0x78d9000 0x400>;
-
- vddcx-supply = <&pm8916_s1_corner>;
- v1p8-supply = <&pm8916_l7>;
- v3p3-supply = <&pm8916_l13>;
-
- clocks = <&gcc GCC_USB_HS_AHB_CLK>,
- <&gcc GCC_USB_HS_SYSTEM_CLK>;
- clock-names = "iface", "core";
-
- resets = <&gcc GCC_USB2A_PHY_BCR>;
- reset-names = "phy";
-
- // D+/D- lines: 1 - Routed to HUB, 0 - Device connector
- switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
- };
-
--
2.45.2
