Re: [PATCH v3 0/6] Bluetooth: hci_qca: use the power sequencer for wcn7850

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 09/07/2024 14:18, Bartosz Golaszewski wrote:
The following series extend the usage of the power sequencing subsystem
in the hci_qca driver.

The end goal is to convert the entire driver to be exclusively pwrseq-based
and simplify it in the process. However due to a large number of users we
need to be careful and consider every case separately.

Right now the only model that fully uses the power sequencer is QCA6390 on
the RB5 board. The next steps are enabling pwrseq for Bluetooth on sm8650
and the X13s laptop. To that end we need to make wcn7850 and wcn6855 aware
of the power sequencing but also keep backward compatibility with older
device trees.

This series contains changes to mainline DT bindings for wcn7850, some
refactoring of the hci_qca driver, making pwrseq the default for the two
models mentioned above and finally modifies the device-tree for sm8650-qrd
to correctly represent the way the Bluetooth module is powered.

I made the last patch part of this series as it has a run-time dependency
on previous changes in it and bluetooth support on the board will break
without them.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>
---
Changes in v3:
- Add a missing break in a switch case
- Link to v2: https://lore.kernel.org/r/20240708-hci_qca_refactor-v2-0-b6e83b3d1ca5@xxxxxxxxxx

Changes in v2:
- Fix a switch issue reported by the test bot
- Link to v1: https://lore.kernel.org/r/20240705-hci_qca_refactor-v1-0-e2442121c13e@xxxxxxxxxx

---
Bartosz Golaszewski (6):
       dt-bindings: bluetooth: qualcomm: describe the inputs from PMU for wcn7850
       Bluetooth: hci_qca: schedule a devm action for disabling the clock
       Bluetooth: hci_qca: unduplicate calls to hci_uart_register_device()
       Bluetooth: hci_qca: make pwrseq calls the default if available
       Bluetooth: hci_qca: use the power sequencer for wcn7850 and wcn6855
       arm64: dts: qcom: sm8650-qrd: use the PMU to power up bluetooth

  .../bindings/net/bluetooth/qualcomm-bluetooth.yaml | 18 +++--
  arch/arm64/boot/dts/qcom/sm8650-qrd.dts            | 28 +++----
  drivers/bluetooth/hci_qca.c                        | 87 +++++++++++++---------
  3 files changed, 72 insertions(+), 61 deletions(-)
---
base-commit: 0b58e108042b0ed28a71cd7edf5175999955b233
change-id: 20240704-hci_qca_refactor-0770e9931fb4

Best regards,

Tested-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx> # on SM8650-QRD

Still works on SM8550-QRD, and properly works with power sequencer on SM8650-QRD

Thanks,
Neil





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux