Soundwire controllers (WSA, WSA2, RX, TX) require reset lines to enable
switching clock control from hardware to software.
Add them along with the reset control providers.
Without this reset we might hit fifo under/over run when we try to write to
soundwire device registers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 09fd6c8e53bb..fa28dbdd1419 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -4,6 +4,7 @@
*/
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,sc8280xp-lpasscc.h>
#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
#include <dt-bindings/clock/qcom,x1e80100-gcc.h>
#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
@@ -3177,6 +3178,8 @@ swr3: soundwire@6ab0000 {
pinctrl-0 = <&wsa2_swr_active>;
pinctrl-names = "default";
+ resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA2_CGCR>;
+ reset-names = "swr_audio_cgcr";
qcom,din-ports = <4>;
qcom,dout-ports = <9>;
@@ -3225,6 +3228,8 @@ swr1: soundwire@6ad0000 {
pinctrl-0 = <&rx_swr_active>;
pinctrl-names = "default";
+ resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
+ reset-names = "swr_audio_cgcr";
qcom,din-ports = <1>;
qcom,dout-ports = <11>;
@@ -3289,6 +3294,8 @@ swr0: soundwire@6b10000 {
pinctrl-0 = <&wsa_swr_active>;
pinctrl-names = "default";
+ resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
+ reset-names = "swr_audio_cgcr";
qcom,din-ports = <4>;
qcom,dout-ports = <9>;
@@ -3309,6 +3316,13 @@ swr0: soundwire@6b10000 {
status = "disabled";
};
+ lpass_audiocc: clock-controller@6b6c000 {
+ compatible = "qcom,x1e80100-lpassaudiocc", "qcom,sc8280xp-lpassaudiocc";
+ reg = <0 0x06b6c000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
swr2: soundwire@6d30000 {
compatible = "qcom,soundwire-v2.0.0";
reg = <0 0x06d30000 0 0x10000>;
@@ -3318,6 +3332,8 @@ swr2: soundwire@6d30000 {
<GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "core", "wakeup";
label = "TX";
+ resets = <&lpasscc LPASS_AUDIO_SWR_TX_CGCR>;
+ reset-names = "swr_audio_cgcr";
pinctrl-0 = <&tx_swr_active>;
pinctrl-names = "default";
@@ -3474,6 +3490,13 @@ data-pins {
};
};
+ lpasscc: clock-controller@6ea0000 {
+ compatible = "qcom,x1e80100-lpasscc", "qcom,sc8280xp-lpasscc";
+ reg = <0 0x06ea0000 0 0x12000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
lpass_ag_noc: interconnect@7e40000 {
compatible = "qcom,x1e80100-lpass-ag-noc";
reg = <0 0x7e40000 0 0xE080>;
--
2.25.1
