PM8008 regulators are used for the cameras found on FP5. Configure the
chip and its voltages.
Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts | 105 ++++++++++++++++++++-
1 file changed, 104 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
index 25ed74d4ebd2..765585b0d09e 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
@@ -207,6 +207,25 @@ active-config0 {
};
};
+ pm8008-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pm8008>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
quiet-thermal {
polling-delay-passive = <0>;
@@ -522,7 +541,76 @@ &gpi_dma1 {
&i2c1 {
status = "okay";
- /* PM8008 PMIC @ 8 and 9 */
+ pm8008: pmic@8 {
+ compatible = "qcom,pm8008";
+ reg = <0x8>;
+
+ interrupts-extended = <&tlmm 25 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&pm8350c_gpios 3 GPIO_ACTIVE_LOW>;
+
+ vdd-l1-l2-supply = <&vreg_s8b>;
+ vdd-l3-l4-supply = <&vreg_bob>;
+ vdd-l5-supply = <&vreg_bob>;
+ vdd-l6-supply = <&vreg_s1b>;
+ vdd-l7-supply = <&vreg_bob>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8008_int_default>, <&pm8008_reset_n_default>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pm8008 0 0 2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ #thermal-sensor-cells = <0>;
+
+ regulators {
+ vreg_l1p: ldo1 {
+ regulator-name = "vreg_l1p";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_l2p: ldo2 {
+ regulator-name = "vreg_l2p";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1152000>;
+ };
+
+ vreg_l3p: ldo3 {
+ regulator-name = "vreg_l3p";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vreg_l4p: ldo4 {
+ regulator-name = "vreg_l4p";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ vreg_l5p: ldo5 {
+ regulator-name = "vreg_l5p";
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ vreg_l6p: ldo6 {
+ regulator-name = "vreg_l6p";
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ vreg_l7p: ldo7 {
+ regulator-name = "vreg_l7p";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ };
+ };
+
/* Pixelworks @ 26 */
/* FSA4480 USB audio switch @ 42 */
/* AW86927FCR haptics @ 5a */
@@ -653,6 +741,14 @@ wide-rfc-therm@4 {
};
};
+&pm8350c_gpios {
+ pm8008_reset_n_default: pm8008-reset-n-default-state {
+ pins = "gpio3";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-pull-down;
+ };
+};
+
&pmk8350_rtc {
status = "okay";
};
@@ -810,6 +906,13 @@ hall_sensor_default: hall-sensor-default-state {
bias-pull-up;
};
+ pm8008_int_default: pm8008-int-default-state {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
pins = "gpio28";
function = "gpio";
--
2.45.2
