Re: [RFC PATCH 2/2] PCI: Add Qualcomm PCIe ECAM root complex driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, May 31, 2024 at 03:47:24PM -0700, Mayank Rana wrote:
> Hi Rob / Mani
> 
> On 4/15/2024 4:30 PM, Mayank Rana wrote:
> > Hi Rob
> > 
> > Excuse me for late response on this (was OOO).
> > On 4/10/2024 9:58 AM, Rob Herring wrote:
> > > On Mon, Apr 08, 2024 at 11:57:58AM -0700, Mayank Rana wrote:
> > > > Hi Mani
> > > > 
> > > > On 4/5/2024 9:17 PM, Manivannan Sadhasivam wrote:
> > > > > On Fri, Apr 05, 2024 at 10:41:15AM -0700, Mayank Rana wrote:
> > > > > > Hi Mani
> > > > > > 
> > > > > > On 4/4/2024 10:30 PM, Manivannan Sadhasivam wrote:
> > > > > > > On Thu, Apr 04, 2024 at 12:11:24PM -0700, Mayank Rana wrote:
> > > > > > > > On some of Qualcomm platform, firmware
> > > > > > > > configures PCIe controller into
> > > > > > > > ECAM mode allowing static memory allocation for
> > > > > > > > configuration space of
> > > > > > > > supported bus range. Firmware also takes care of
> > > > > > > > bringing up PCIe PHY
> > > > > > > > and performing required operation to bring PCIe
> > > > > > > > link into D0. Firmware
> > > > > > > > also manages system resources (e.g.
> > > > > > > > clocks/regulators/resets/ bus voting).
> > > > > > > > Hence add Qualcomm PCIe ECAM root complex driver
> > > > > > > > which enumerates PCIe
> > > > > > > > root complex and connected PCIe devices.
> > > > > > > > Firmware won't be enumerating
> > > > > > > > or powering up PCIe root complex until this
> > > > > > > > driver invokes power domain
> > > > > > > > based notification to bring PCIe link into D0/D3cold mode.
> > > > > > > > 
> > > > > > > 
> > > > > > > Is this an in-house PCIe IP of Qualcomm or the same
> > > > > > > DWC IP that is used in other
> > > > > > > SoCs?
> > > > > > > 
> > > > > > > - Mani
> > > > > > Driver is validated on SA8775p-ride platform using PCIe DWC IP for
> > > > > > now.Although this driver doesn't need to know used PCIe
> > > > > > controller and PHY
> > > > > > IP as well programming sequence as that would be taken
> > > > > > care by firmware.
> > > > > > 
> > > > > 
> > > > > Ok, so it is the same IP but firmware is controlling the
> > > > > resources now. This
> > > > > information should be present in the commit message.
> > > > > 
> > > > > Btw, there is an existing generic ECAM host controller driver:
> > > > > drivers/pci/controller/pci-host-generic.c
> > > > > 
> > > > > This driver is already being used by several vendors as
> > > > > well. So we should try
> > > > > to extend it for Qcom usecase also.
> > > 
> > > I would take it a bit further and say if you need your own driver, then
> > > just use the default QCom driver. Perhaps extend it to support ECAM.
> > > Better yet, copy your firmware setup and always configure the QCom h/w
> > > to use ECAM.
> > Good suggestion. Although here we are having 2 set of requirements:
> > 1. ECAM configuration
> > 2. Managing PCIe controller and PHY resources and programming from
> > firmware as well
> > Hence it is not feasible to use default QCOM driver.
> > > If you want to extend the generic driver, that's fine, but we don't need
> > > a 3rd.
> > I did consider this part before coming up with new driver. Although I
> > felt that
> > below mentioned functionality may not look more generic to be part of
> > pci-host-generic.c driver.
> > > > I did review pci-host-generic.c driver for usage. although there
> > > > are more
> > > > functionalityneeded for use case purpose as below:
> > > > 1. MSI functionality
> > > 
> > > Pretty sure the generic driver already supports that.
> > I don't find any MSI support with pci-host-generic.c driver.
> > > > 2. Suspend/Resume
> > > 
> > > Others might want that to work as well.
> > Others firmware won't have way to handle D3cold and D0 functionality
> > handling as
> > needed here for supporting suspend/resume as I don't find any interface
> > for pci-host-generic.c driver to notify firmware. here we are having way
> > to talk to firmware using GenPD based power domain usage to communicate
> > with firmware.
> > 
> > > > 3. Wakeup Functionality (not part of current change, but would be added
> > > > later)
> > > 
> > > Others might want that to work as well.
> > possible if suspend/resume support is available or used.
> > > > 4. Here this driver provides way to virtualized PCIe controller.
> > > > So VMs only
> > > > talk to a generic ECAM whereas HW is only directed accessed by
> > > > service VM.
> > > 
> > > That's the existing driver. If if doesn't work for a VM, fix the VM.
> > Correct.
> > > > 5. Adding more Auto based safety use cases related implementation
> > > 
> > > Now that's just hand waving.
> > Here I am trying to provide new set of changes plan to be added as part
> > of required functionality.
> > 
> > > > Hence keeping pci-host-generic.c as generic driver where above
> > > > functionality
> > > > may not be needed.
> > > 
> > > Duplicating things to avoid touching existing drivers is not how kernel
> > > development works.
> > I shall try your suggestion and see how it looks in terms of code
> > changes. Perhaps then we can have more clarity in terms of adding more
> > functionality into generic or having separate driver.
> I just learnt that previously dwc related PCIe ECAM driver and MSI
> controller driver tried out as:
> 
> https://lore.kernel.org/linux-pci/20170821192907.8695-1-ard.biesheuvel@xxxxxxxxxx/
> 
> Although there were few concerns at that time. Due to that having dwc
> specific MSI functionality based driver was dropped, and pci-host-generic.c
> driver is being updated using with dwc/snps specific ECAM operation.
> 
> In current discussion, it seems that we are discussing to have identical
> approach here.
> 
> Atleast on Qualcomm SA8775p platform, I don't have any other way to support
> MSI functionality i.e. extended SPI or ITS/LPI based MSI or using GICv2m
> functionality are not supported.
> 
> I don't see any other approach other than MSI based implementation within
> pci-host-generic.c driver for dwc/snps based MSI controller.
> 
> Do you have any suggestion on this ?
> 

Since this ECAM driver is going to be used in newer Qcom SoCs, why can't you use
GICv3 for MSI handling?

- Mani

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux