Re: [PATCH v3 5/7] drm/msm/hdmi: make use of the drm_connector_hdmi framework

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, May 30, 2024 at 11:16:08AM +0200, Maxime Ripard wrote:
> Hi,
> 
> On Thu, May 30, 2024 at 02:12:28AM GMT, Dmitry Baryshkov wrote:
> > Setup the HDMI connector on the MSM HDMI outputs. Make use of
> > atomic_check hook and of the provided Infoframe infrastructure.
> > 
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> 
> As a general comment: I really like it, it looks super tidy. Thanks!
> 
> There's a couple of minor issues below
> 
> > -int msm_hdmi_audio_update(struct hdmi *hdmi)
> > +static int msm_hdmi_audio_update(struct hdmi *hdmi)
> >  {
> >  	struct hdmi_audio *audio = &hdmi->audio;
> > -	struct hdmi_audio_infoframe *info = &audio->infoframe;
> >  	const struct hdmi_msm_audio_arcs *arcs = NULL;
> >  	bool enabled = audio->enabled;
> >  	uint32_t acr_pkt_ctrl, vbi_pkt_ctrl, aud_pkt_ctrl;
> > -	uint32_t infofrm_ctrl, audio_config;
> > +	uint32_t audio_config;
> > +
> > +	if (!hdmi->hdmi_mode)
> > +		return -EINVAL;
> > +
> > +	DBG("audio: enabled=%d, channels=%d, rate=%d",
> > +	    audio->enabled, audio->channels, audio->rate);
> >  
> > -	DBG("audio: enabled=%d, channels=%d, channel_allocation=0x%x, "
> > -		"level_shift_value=%d, downmix_inhibit=%d, rate=%d",
> > -		audio->enabled, info->channels,  info->channel_allocation,
> > -		info->level_shift_value, info->downmix_inhibit, audio->rate);
> >  	DBG("video: power_on=%d, pixclock=%lu", hdmi->power_on, hdmi->pixclock);
> 
> pixclock should come from the connector state too. It's still calculated
> by the driver in msm_hdmi_bridge_mode_set

Yes, that's why I asked on IRC regarding the char rate and ALSA codec.
I'll see what I can do.

> 
> > @@ -341,8 +425,11 @@ int msm_hdmi_bridge_init(struct hdmi *hdmi)
> >  	bridge->funcs = &msm_hdmi_bridge_funcs;
> >  	bridge->ddc = hdmi->i2c;
> >  	bridge->type = DRM_MODE_CONNECTOR_HDMIA;
> > +	bridge->vendor = "Qualcomm";
> > +	bridge->product = "Snapdragon";
> >  	bridge->ops = DRM_BRIDGE_OP_HPD |
> >  		DRM_BRIDGE_OP_DETECT |
> > +		DRM_BRIDGE_OP_HDMI |
> >  		DRM_BRIDGE_OP_EDID;
> >  
> >  	ret = devm_drm_bridge_add(hdmi->dev->dev, bridge);
> 
> It looks like you're not setting either the supported formats or bpc?

I've added what looks to be sane defaults to the drm_bridge_connector:
RGB only and bpc = 8. If at some point we get to YUV or HDR support,
that would need to be reflected here.




-- 
With best wishes
Dmitry




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux