[PATCH RESEND2 v5 0/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
Box Core board based on the Qualcomm APQ8016E SoC. For more information
refer to the product page [1].

One of the major difference from db410c is serial port where HMIBSC board
uses UART1 as the debug console with a default RS232 mode (UART1 mode mux
configured via gpio99 and gpio100).

Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 1GiB RAM
- 8GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
- USB ethernet adaptors (soldered)

This series is a v2 since v1 of this DTS file has been reviewed on the
U-Boot mailing list [2].

Changes in v5:
- Resend again as the v6.10-rc1 is out.
- Addressed another nitpick from Stephen.
- Collected Stephen's review tag.
- Warnings reported by Rob's DT check bot aren't related to HMIBSC
  board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
  still not converted to YAML format.

Changes in v4:
- Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations
  of Linux kernel driver. Instead depend on systemd workaround suggested
  by Caleb to get expected HMIBSC reset behaviour.
- Incorporated further DT coding style comments from Stephen.
- Warnings reported by Rob's DT check bot aren't related to HMIBSC
  board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt
  still not converted to YAML format.

Changes in v3:
- Picked up tags.
- Fixed further DT schema warnings.
- Configure resin/power button interrupt as falling edge.
- Incorporate DTS coding style comments from Krzysztof and Konrad.

Changes in v2:
- Fix DT schema warnings.
- Incorporate suggestions from Stephan.
- Document UART1 mode GPIOs based mux.

[1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@xxxxxxxxxx/

Sumit Garg (3):
  dt-bindings: vendor-prefixes: Add Schneider Electric
  dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board
  arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/apq8016-schneider-hmibsc.dts     | 491 ++++++++++++++++++
 4 files changed, 495 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts

-- 
2.34.1





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux