Re: [PATCH v16 0/2] Add DT support for Multiport controller on SC8280XP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 29 Apr 2024 21:50:46 +0530, Krishna Kurapati wrote:
> Series [1] introduces binding and driver support for DWC3 Multiport
> controllers. This series adds support for tertiary controller of SC8280
> and enabled multiport controller for SA8295P-ADP platform.
> 
> Till v13 [2] the DT was pushed along with driver code. Separated the DT
> changes from driver update and pushing it as this series. The first two
> versions were marked as v1 and v2. Marked this as v16 to avoid missing
> of change log till v13.
> 
> Changes in v16:
> Marked it as v16 rather than v3 since till v13, there were DT changes
> sent along with driver code but were separated and this version is
> supposed to be v16.
> Fixed interrupt triggers from EDGE_RISING to EDGE_BOTH.
> 
> Link to v15:
> https://lore.kernel.org/all/20240213082724.1789096-1-quic_kriskura@xxxxxxxxxxx/
> 
> Changes in v15:
> SA8540 Ride related code changes have been dropped and will pushed later
> due to unavailability of hardware with either Andrew or me for testing the
> gpio hog changes suggested in v1.
> Implemented vbus boost regulators as fixed regulators instead of modelling
> their enable pins as pinctrl nodes.
> 
> Link to v14:
> https://lore.kernel.org/all/20240206114745.1388491-1-quic_kriskura@xxxxxxxxxxx/
> 
> [1]: https://lore.kernel.org/all/20240420044901.884098-1-quic_kriskura@xxxxxxxxxxx/
> [2]: https://lore.kernel.org/all/20231007154806.605-1-quic_kriskura@xxxxxxxxxxx/#r
> 
> Krishna Kurapati (2):
>   arm64: dts: qcom: sc8280xp: Add USB DWC3 Multiport controller
>   arm64: dts: qcom: sa8295p: Enable tertiary controller and its 4 USB
>     ports
> 
>  arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 83 ++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sc8280xp.dtsi   | 82 +++++++++++++++++++++++
>  2 files changed, 165 insertions(+)
> 
> --
> 2.34.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y qcom/sa8295p-adp.dtb' for 20240429162048.2133512-1-quic_kriskura@xxxxxxxxxxx:

arch/arm64/boot/dts/qcom/sa8295p-adp.dtb: usb@a4f8800: interrupt-names: ['pwr_event_1', 'pwr_event_2', 'pwr_event_3', 'pwr_event_4', 'hs_phy_1', 'hs_phy_2', 'hs_phy_3', 'hs_phy_4', 'dp_hs_phy_1', 'dm_hs_phy_1', 'dp_hs_phy_2', 'dm_hs_phy_2', 'dp_hs_phy_3', 'dm_hs_phy_3', 'dp_hs_phy_4', 'dm_hs_phy_4', 'ss_phy_1', 'ss_phy_2'] is too long
	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
arch/arm64/boot/dts/qcom/sa8295p-adp.dtb: usb@a4f8800: interrupts-extended: [[1, 0, 130, 4], [1, 0, 135, 4], [1, 0, 857, 4], [1, 0, 856, 4], [1, 0, 131, 4], [1, 0, 136, 4], [1, 0, 860, 4], [1, 0, 859, 4], [118, 127, 3], [118, 126, 3], [118, 129, 3], [118, 128, 3], [118, 131, 3], [118, 130, 3], [118, 133, 3], [118, 132, 3], [118, 16, 4], [118, 17, 4]] is too long
	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#









[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux