Re: [PATCH 10/10] arm64: dts: qcom: Add AYN Odin 2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 24/04/2024 17:29, Xilin Wu via B4 Relay wrote:
> From: Xilin Wu <wuxilin123@xxxxxxxxx>
> 
> AYN Odin 2 is a gaming handheld based on QCS8550, which is derived
> from SM8550 but without modem RF system.
> 



> +
> +/ {
> +	model = "AYN Odin 2";
> +	compatible = "ayn,odin2", "qcom,qcs8550", "qcom,sm8550";
> +	chassis-type = "handset";
> +
> +	qcom,msm-id = <QCOM_ID_QCS8550 0x20000>;
> +	qcom,board-id = <0x1001f 0>;

No, these are not allowed. You did not test your dts.

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +
> +	aliases {
> +		serial0 = &uart7;
> +		serial1 = &uart14;
> +		serial2 = &uart15;
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pmk8550_pwm 0 860000>;
> +		brightness-levels = <1023 0>;
> +		num-interpolated-steps = <1023>;
> +		default-brightness-level = <600>;
> +		power-supply = <&vph_pwr>;
> +		enable-gpios = <&pmk8550_gpios 5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pwm_backlight_default>;
> +		status = "okay";

Drop, why do you need it? Do you see it anywhere else in the backlight
nodes in DTS?


> +	};
> +
> +	fan_pwr: fan-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fan_pwr";
> +
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&fan_pwr_en>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-0 = <&volume_up_n>, <&m1_m2_keys_default>;
> +		pinctrl-names = "default";
> +
> +		key-volume-up {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <15>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +
> +		m1-button {
> +			label = "M1";
> +			linux,code = <BTN_TRIGGER_HAPPY1>;
> +			gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		m2-button {
> +			label = "M2";
> +			linux,code = <BTN_TRIGGER_HAPPY2>;
> +			gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "d";
> +		hpd-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&lt8912_out>;
> +			};
> +		};
> +	};
> +
> +	hdmi_pwr: hdmi-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "hdmi_pwr";
> +
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +
> +		gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	vdd_lcm_2p8: vdd-lcm-2p8-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_lcm_2p8";
> +
> +		regulator-min-microvolt = <2800000>;
> +		regulator-max-microvolt = <2800000>;
> +
> +		gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	led_left_side: led-controller-1 {
> +		compatible = "pwm-leds-multicolor";
> +
> +		multi-led {
> +			label = "left-side";
> +			color = <LED_COLOR_ID_RGB>;
> +			max-brightness = <255>;
> +
> +			led-red {
> +				color = <LED_COLOR_ID_RED>;
> +				pwms = <&pwm_rgb_left 0>;
> +			};
> +
> +			led-green {
> +				color = <LED_COLOR_ID_GREEN>;
> +				pwms = <&pwm_rgb_left 1>;
> +			};
> +
> +			led-blue {
> +				color = <LED_COLOR_ID_BLUE>;
> +				pwms = <&pwm_rgb_left 2>;
> +			};
> +		};
> +	};
> +
> +	led_left_joystick: led-controller-2 {
> +		compatible = "pwm-leds-multicolor";
> +
> +		multi-led {
> +			label = "left-joystick";
> +			color = <LED_COLOR_ID_RGB>;
> +			max-brightness = <255>;
> +
> +			led-red {
> +				color = <LED_COLOR_ID_RED>;
> +				pwms = <&pwm_rgb_left 6>;
> +			};
> +
> +			led-green {
> +				color = <LED_COLOR_ID_GREEN>;
> +				pwms = <&pwm_rgb_left 7>;
> +			};
> +
> +			led-blue {
> +				color = <LED_COLOR_ID_BLUE>;
> +				pwms = <&pwm_rgb_left 8>;
> +			};
> +		};
> +	};
> +
> +	led_right_side: led-controller-3 {
> +		compatible = "pwm-leds-multicolor";
> +
> +		multi-led {
> +			label = "right-side";
> +			color = <LED_COLOR_ID_RGB>;
> +			max-brightness = <255>;
> +
> +			led-red {
> +				color = <LED_COLOR_ID_RED>;
> +				pwms = <&pwm_rgb_right 0>;
> +			};
> +
> +			led-green {
> +				color = <LED_COLOR_ID_GREEN>;
> +				pwms = <&pwm_rgb_right 1>;
> +			};
> +
> +			led-blue {
> +				color = <LED_COLOR_ID_BLUE>;
> +				pwms = <&pwm_rgb_right 2>;
> +			};
> +		};
> +	};
> +
> +	led_right_joystick: led-controller-4 {
> +		compatible = "pwm-leds-multicolor";
> +
> +		multi-led {
> +			label = "right-joystick";
> +			color = <LED_COLOR_ID_RGB>;
> +			max-brightness = <255>;
> +
> +			led-red {
> +				color = <LED_COLOR_ID_RED>;
> +				pwms = <&pwm_rgb_right 6>;
> +			};
> +
> +			led-green {
> +				color = <LED_COLOR_ID_GREEN>;
> +				pwms = <&pwm_rgb_right 7>;
> +			};
> +
> +			led-blue {
> +				color = <LED_COLOR_ID_BLUE>;
> +				pwms = <&pwm_rgb_right 8>;
> +			};
> +		};
> +	};
> +
> +	mcu_3v3: mcu-3v3-regulator {

Name all regulators regulator-n, where n is decimal number. Then order
the nodes by name.


...

> +
> +&i2c4 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	touchscreen@20 {
> +		compatible = "syna,rmi4-i2c";
> +		reg = <0x20>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		interrupts-extended = <&tlmm 25 0x2008>;
> +
> +		pinctrl-names = "default", "sleep";
> +		pinctrl-0 = <&ts_int_default>;
> +		pinctrl-1 = <&ts_int_sleep>;
> +
> +		vio-supply = <&vreg_l12b_1p8>;
> +
> +		syna,startup-delay-ms = <200>;
> +		syna,reset-delay-ms = <200>;
> +
> +		rmi4-f01@1 {
> +			syna,nosleep-mode = <0x1>;
> +			reg = <0x1>;
> +		};
> +
> +		rmi4-f12@12 {
> +			reg = <0x12>;
> +			syna,rezero-wait-ms = <20>;
> +			syna,clip-x-low = <0>;
> +			syna,clip-y-low = <0>;
> +			syna,clip-x-high = <1080>;
> +			syna,clip-y-high = <1920>;
> +			syna,sensor-type = <1>;
> +			touchscreen-inverted-x;
> +		};
> +	};

Please confirm the status of dtbs_check for your board. I am pretty sure
it fails.

Best regards,
Krzysztof





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux