There are two issues with SDHC2 configuration for SA8155P-ADP,
which prevent use of SDHC2 and causes issues with ethernet:
- Card Detect pin for SHDC2 on SA8155P-ADP is connected to gpio4 of
PMM8155AU_1, not to SoC itself. SoC's gpio4 is used for DWMAC
TX. If sdhc driver probes after dwmac driver, it reconfigures
gpio4 and this breaks Ethernet MAC.
- pinctrl configuration mentions gpio96 as CD pin. It seems it was
copied from some SM8150 example, because as mentioned above,
correct CD pin is gpio4 on PMM8155AU_1.
This patch fixes both mentioned issues by providing correct pin handle
and pinctrl configuration.
Fixes: 0deb2624e2d0 ("arm64: dts: qcom: sa8155p-adp: Add support for uSD card")
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@xxxxxxxx>
---
In v3:
- Moved regulator changes to a separate patch
- Renamed pinctrl node
- Moved pinctrl node so it will appear in alphabetical order
In v2:
- Added "Fixes:" tag
- CCed stable ML
- Fixed pinctrl configuration
- Extended voltage range for L13C voltage regulator
---
arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 30 ++++++++++--------------
1 file changed, 13 insertions(+), 17 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
index 5e4287f8c8cd1..b2cf2c988336c 100644
--- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -367,6 +367,16 @@ queue0 {
};
};
+&pmm8155au_1_gpios {
+ pmm8155au_1_sdc2_cd: sdc2-cd-default-state {
+ pins = "gpio4";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ power-source = <0>;
+ };
+};
+
&qupv3_id_1 {
status = "okay";
};
@@ -384,10 +394,10 @@ &remoteproc_cdsp {
&sdhc_2 {
status = "okay";
- cd-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&pmm8155au_1_gpios 4 GPIO_ACTIVE_LOW>;
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_on>;
- pinctrl-1 = <&sdc2_off>;
+ pinctrl-0 = <&sdc2_on &pmm8155au_1_sdc2_cd>;
+ pinctrl-1 = <&sdc2_off &pmm8155au_1_sdc2_cd>;
vqmmc-supply = <&vreg_l13c_2p96>; /* IO line power */
vmmc-supply = <&vreg_l17a_2p96>; /* Card power line */
bus-width = <4>;
@@ -505,13 +515,6 @@ data-pins {
bias-pull-up; /* pull up */
drive-strength = <16>; /* 16 MA */
};
-
- sd-cd-pins {
- pins = "gpio96";
- function = "gpio";
- bias-pull-up; /* pull up */
- drive-strength = <2>; /* 2 MA */
- };
};
sdc2_off: sdc2-off-state {
@@ -532,13 +535,6 @@ data-pins {
bias-pull-up; /* pull up */
drive-strength = <2>; /* 2 MA */
};
-
- sd-cd-pins {
- pins = "gpio96";
- function = "gpio";
- bias-pull-up; /* pull up */
- drive-strength = <2>; /* 2 MA */
- };
};
usb2phy_ac_en1_default: usb2phy-ac-en1-default-state {
--
2.44.0
