On 4/2/2024 3:22 AM, Dmitry Baryshkov wrote:
On Mon, 1 Apr 2024 at 12:40, Tengfei Fan <quic_tengfan@xxxxxxxxxxx> wrote:Add AIM300 AIoT Carrier board DTS support, including usb, UART, PCIe, I2C functions support. Here is a diagram of AIM300 AIoT Carrie Board and SoM +--------------------------------------------------+ | AIM300 AIOT Carrie Board | | | | +-----------------+ | |power----->| Fixed regulator |---------+ | | +-----------------+ | | | | | | v VPH_PWR | | +----------------------------------------------+ | | | AIM300 SOM | | | | | |VPH_PWR | | | | v | | | | +-------+ +--------+ +------+ | | | | | UFS | | QCS8550| |PMIC | | | | | +-------+ +--------+ +------+ | | | | | | | +----------------------------------------------+ | | | | +----+ +------+ | | |USB | | UART | | | +----+ +------+ | +--------------------------------------------------+ Co-developed-by: Qiang Yu <quic_qianyu@xxxxxxxxxxx> Signed-off-by: Qiang Yu <quic_qianyu@xxxxxxxxxxx> Co-developed-by: Ziyue Zhang <quic_ziyuzhan@xxxxxxxxxxx> Signed-off-by: Ziyue Zhang <quic_ziyuzhan@xxxxxxxxxxx> Signed-off-by: Tengfei Fan <quic_tengfan@xxxxxxxxxxx> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/qcs8550-aim300-aiot.dts | 384 ++++++++++++++++++ 2 files changed, 385 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 7d40ec5e7d21..02d9bc3bfce7 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -96,6 +96,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb +dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb dtb-$(CONFIG_ARCH_QCOM) += qrb4210-rb2.dtb diff --git a/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts new file mode 100644 index 000000000000..8188766c3d84 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts @@ -0,0 +1,384 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2023-2024, Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include "qcs8550-aim300.dtsi" +#include "pm8010.dtsi" +#include "pmr735d_a.dtsi" +#include "pmr735d_b.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. QCS8550 AIM300 AIOT"; + compatible = "qcom,qcs8550-aim300-aiot", "qcom,qcs8550-aim300", "qcom,qcs8550", + "qcom,sm8550"; + + aliases { + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&volume_up_n>; + pinctrl-names = "default"; + + key-volume-up { + label = "Volume Up"; + debounce-interval = <15>; + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + linux,can-disable; + wakeup-source; + }; + }; + + pmic-glink { + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink"; + #address-cells = <1>; + #size-cells = <0>; + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_hs_in: endpoint { + remote-endpoint = <&usb_1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss_in: endpoint { + remote-endpoint = <&redriver_ss_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_sbu: endpoint { + remote-endpoint = <&fsa4480_sbu_mux>; + }; + }; + }; + }; + }; + + vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + vdd-bob1-supply = <&vph_pwr>; + vdd-bob2-supply = <&vph_pwr>; + }; + + regulators-3 { + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + }; + + regulators-4 { + vdd-s4-supply = <&vph_pwr>; + }; + + regulators-5 { + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + }; +}; + +&i2c_hub_2 { + status = "okay"; + + typec-mux@42 { + compatible = "fcs,fsa4480"; + reg = <0x42>; + + vcc-supply = <&vreg_bob1>; + + mode-switch; + orientation-switch; + + port { + fsa4480_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_sbu>; + }; + }; + }; + + typec-retimer@1c { + compatible = "onnn,nb7vpq904m"; + reg = <0x1c>; + + vcc-supply = <&vreg_l15b_1p8>; + + orientation-switch; + retimer-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + redriver_ss_out: endpoint { + remote-endpoint = <&pmic_glink_ss_in>; + }; + }; + + port@1 { + reg = <1>; + + redriver_ss_in: endpoint { + data-lanes = <3 2 1 0>; + remote-endpoint = <&usb_dp_qmpphy_out>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l3e_1p2>;Is this wired on the carrier board or on the AIC300 SoM?
I checked schematic diagram, this should be on the AIM300 SoM.
+ status = "okay"; + + panel@0 { + compatible = "visionox,vtdr6130"; + reg = <0>; + + pinctrl-0 = <&dsi_active>, <&te_active>; + pinctrl-1 = <&dsi_suspend>, <&te_suspend>; + pinctrl-names = "default", "sleep"; + + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; + + vci-supply = <&vreg_l13b_3p0>; + vdd-supply = <&vreg_l11b_1p2>; + vddio-supply = <&vreg_l12b_1p8>; + + port { + panel0_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&panel0_in>; + data-lanes = <0 1 2 3>; +}; + +&mdss_dsi0_phy { + vdds-supply = <&vreg_l1e_0p88>;This too
This also should be on the AIM300 SoM.
+ status = "okay"; +}; + +&pcie0 { + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;And this
I checked schematic diagram, this should be on the AIM300 SoM.
+ + pinctrl-0 = <&pcie0_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie0_phy { + vdda-phy-supply = <&vreg_l1e_0p88>; + vdda-pll-supply = <&vreg_l3e_1p2>;You guess the question. I think I'll stop here. Please review your changes here, which are really specific to the carrier board and which apply to the SoM.
I will review this change totally, then I will distinguish all these nodes which are on the carrier board and which are on the AIM300 SoM. Then I will update change series.
+ + status = "okay"; +}; + +&pcie_1_phy_aux_clk { + clock-frequency = <1000>; +}; + +&pcie1 { + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&pcie1_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie1_phy { + vdda-phy-supply = <&vreg_l3c_0p9>; + vdda-pll-supply = <&vreg_l3e_1p2>; + vdda-qref-supply = <&vreg_l1e_0p88>; + + status = "okay"; +}; + +&pm8550_gpios { + volume_up_n: volume-up-n-state { + pins = "gpio6"; + function = "normal"; + power-source = <1>; + bias-pull-up; + input-enable; + }; +}; + +&pm8550b_eusb2_repeater { + vdd18-supply = <&vreg_l15b_1p8>; + vdd3-supply = <&vreg_l5b_3p1>; +}; + + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs8550/adsp.mbn", + "qcom/qcs8550/adsp_dtbs.elf"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs8550/cdsp.mbn", + "qcom/qcs8550/cdsp_dtbs.elf"; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&swr1 { + status = "okay"; +}; + +&swr2 { + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <32 8>; + + dsi_active: dsi-active-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + dsi_suspend: dsi-suspend-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + te_active: te-active-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; + + te_suspend: te-suspend-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; +}; + +&uart7 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_dwc3_hs { + remote-endpoint = <&pmic_glink_hs_in>; +}; + +&usb_1_dwc3_ss { + remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>; +}; + +&usb_1_hsphy { + phys = <&pm8550b_eusb2_repeater>; + + vdd-supply = <&vreg_l1e_0p88>; + vdda12-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&usb_dp_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l3f_0p88>; + + orientation-switch; + + status = "okay"; +}; + +&usb_dp_qmpphy_out { + remote-endpoint = <&redriver_ss_in>; +}; + +&usb_dp_qmpphy_usb_ss_in { + remote-endpoint = <&usb_1_dwc3_ss>; +}; + +&xo_board { + clock-frequency = <76800000>; +}; -- 2.25.1
-- Thx and BRs, Tengfei Fan
