From: Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>
Add support for a new SPMI vibrator module which is very similar
to the vibrator module inside PM8916 but has a finer drive voltage
step and different output voltage range, its drive level control
is expanded across 2 registers. The vibrator module can be found
in following Qualcomm PMICs: PMI632, PM7250B, PM7325B, PM7550BA.
Signed-off-by: Fenglin Wu <quic_fenglinw@xxxxxxxxxxx>
---
drivers/input/misc/pm8xxx-vibrator.c | 49 +++++++++++++++++++++++++++++-------
1 file changed, 40 insertions(+), 9 deletions(-)
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index 3b6a2e949f30..59548cd9331c 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -12,9 +12,9 @@
#include <linux/regmap.h>
#include <linux/slab.h>
-#define VIB_MAX_LEVEL_mV (3100)
-#define VIB_MIN_LEVEL_mV (1200)
-#define VIB_MAX_LEVELS (VIB_MAX_LEVEL_mV - VIB_MIN_LEVEL_mV)
+#define VIB_MAX_LEVEL_mV(vib) (vib->drv2_addr ? (3544) : (3100))
+#define VIB_MIN_LEVEL_mV(vib) (vib->drv2_addr ? (1504) : (1200))
+#define VIB_MAX_LEVELS(vib) (VIB_MAX_LEVEL_mV(vib) - VIB_MIN_LEVEL_mV(vib))
#define MAX_FF_SPEED 0xff
@@ -25,6 +25,9 @@ struct pm8xxx_regs {
unsigned int drv_offset;
unsigned int drv_mask;
unsigned int drv_shift;
+ unsigned int drv2_offset;
+ unsigned int drv2_mask;
+ unsigned int drv2_shift;
unsigned int drv_en_manual_mask;
};
@@ -44,6 +47,18 @@ static struct pm8xxx_regs pm8916_regs = {
.drv_en_manual_mask = 0,
};
+static struct pm8xxx_regs pmi632_regs = {
+ .enable_offset = 0x46,
+ .enable_mask = BIT(7),
+ .drv_offset = 0x40,
+ .drv_mask = 0xFF,
+ .drv_shift = 0,
+ .drv2_offset = 0x41,
+ .drv2_mask = 0x0F,
+ .drv2_shift = 8,
+ .drv_en_manual_mask = 0,
+};
+
/**
* struct pm8xxx_vib - structure to hold vibrator data
* @vib_input_dev: input device supporting force feedback
@@ -52,6 +67,7 @@ static struct pm8xxx_regs pm8916_regs = {
* @regs: registers' info
* @enable_addr: vibrator enable register
* @drv_addr: vibrator drive strength register
+ * @drv2_addr: vibrator drive strength upper byte register
* @speed: speed of vibration set from userland
* @active: state of vibrator
* @level: level of vibration to set in the chip
@@ -64,6 +80,7 @@ struct pm8xxx_vib {
const struct pm8xxx_regs *regs;
unsigned int enable_addr;
unsigned int drv_addr;
+ unsigned int drv2_addr;
int speed;
int level;
bool active;
@@ -92,6 +109,16 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
vib->reg_vib_drv = val;
+ if (regs->drv2_mask) {
+ if (on)
+ val = (vib->level << regs->drv2_shift) & regs->drv2_mask;
+ else
+ val = 0;
+ rc = regmap_write(vib->regmap, vib->drv2_addr, val);
+ if (rc < 0)
+ return rc;
+ }
+
if (regs->enable_mask)
rc = regmap_update_bits(vib->regmap, vib->enable_addr,
regs->enable_mask, on ? ~0 : 0);
@@ -114,19 +141,22 @@ static void pm8xxx_work_handler(struct work_struct *work)
return;
/*
- * pmic vibrator supports voltage ranges from 1.2 to 3.1V, so
+ * pmic vibrator supports voltage ranges from MIN_LEVEL to MAX_LEVEL, so
* scale the level to fit into these ranges.
*/
if (vib->speed) {
vib->active = true;
- vib->level = ((VIB_MAX_LEVELS * vib->speed) / MAX_FF_SPEED) +
- VIB_MIN_LEVEL_mV;
- vib->level /= 100;
+ vib->level = ((VIB_MAX_LEVELS(vib) * vib->speed) / MAX_FF_SPEED) +
+ VIB_MIN_LEVEL_mV(vib);
} else {
vib->active = false;
- vib->level = VIB_MIN_LEVEL_mV / 100;
+ vib->level = VIB_MIN_LEVEL_mV(vib);
+
}
+ if (!vib->drv2_addr)
+ vib->level /= 100;
+
pm8xxx_vib_set(vib, vib->active);
}
@@ -202,7 +232,7 @@ static int pm8xxx_vib_probe(struct platform_device *pdev)
vib->enable_addr = reg_base + regs->enable_offset;
vib->drv_addr = reg_base + regs->drv_offset;
-
+ vib->drv2_addr = reg_base + regs->drv2_offset;
/* operate in manual mode */
error = regmap_read(vib->regmap, vib->drv_addr, &val);
if (error < 0)
@@ -256,6 +286,7 @@ static const struct of_device_id pm8xxx_vib_id_table[] = {
{ .compatible = "qcom,pm8058-vib", .data = &pm8058_regs },
{ .compatible = "qcom,pm8921-vib", .data = &pm8058_regs },
{ .compatible = "qcom,pm8916-vib", .data = &pm8916_regs },
+ { .compatible = "qcom,pmi632-vib", .data = &pmi632_regs },
{ }
};
MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
--
2.25.1
