Re: [PATCH 2/3] arm64: dts: qcom: sm8650: add support for the SM8650-HDK board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Neil,

On 2/23/24 10:52, Neil Armstrong wrote:
The SM8650-HDK is an embedded development platforms for the
Snapdragon 8 Gen 3 SoC aka SM8650, with the following features:
- Qualcomm SM8650 SoC
- 16GiB On-board LPDDR5
- On-board WiFi 7 + Bluetooth 5.3/BLE
- On-board UFS4.0
- M.2 Key B+M Gen3x2 PCIe Slot
- HDMI Output
- USB-C Connector with DP Almode & Audio Accessory mode
- Micro-SDCard Slot
- Audio Jack with Playback and Microphone
- 2 On-board Analog microphones
- 2 On-board Speakers
- 96Boards Compatible Low-Speed and High-Speed connectors [1]
   - For Camera, Sensors and external Display cards
     - Compatible with the Linaro Debug board [2]

what are these [1] and [2] references? Probably there might be some links.

     - SIM Slot for Modem
     - Debug connectors
     - 6x On-Board LEDs

Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/Makefile       |    1 +
  arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 1259 +++++++++++++++++++++++++++++++
  2 files changed, 1260 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..4f48c98451de 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx224.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-hdk.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
new file mode 100644
index 000000000000..cb1e0f569483

<snip>

+
+&i2c6 {
+	clock-frequency = <400000>;
+	status = "okay";
+

<snip>

+};
+
+&i2c3 {
+       status = "okay";
+

<snip>

+};

Please change the order of i2c3 and i2c6.

<snip>

+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+

May be put the clock above after &pcie1_phy like in the list of gcc
source clocks?

+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1i_0p88>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3e_0p9>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+	vdda-qref-supply = <&vreg_l1i_0p88>;
+
+	status = "okay";
+};
+

So I've found just these minor things, and I've successfully tested
the dtb on the SM8650-HDK board.

Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@xxxxxxxxxx>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@xxxxxxxxxx>

--
Best wishes,
Vladimir




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux