[PATCH 3/3] arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay

[Neil Armstrong <neil.armstrong@xxxxxxxxxx>]

With the SM8650-HDK, a Display Card kit can be connected to provide
a VTDR6130 display with Goodix Berlin Touch controller.

In order to route the DSI lanes to the connector for the Display
Card kit, a switch must be changed on the board.

The HDMI nodes are disabled since the DSI lanes are shared with
the DSI to HDMI transceiver.

Add support for this card as an overlay and apply it it at
build-time to the sm8650-hdk dtb.

Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   4 +
 .../boot/dts/qcom/sm8650-hdk-display-card.dtso     | 151 +++++++++++++++++++++
 2 files changed, 155 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4f48c98451de..566997db4b37 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx224.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
+
+sm8650-hdk-display-card-dtbs	:= sm8650-hdk.dtb sm8650-hdk-display-card.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-hdk-display-card.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso b/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso
new file mode 100644
index 000000000000..b9de6c9ce10e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Linaro Limited
+ */
+
+/*
+ * Display Card kit overlay
+ * This requires S5702 Switch 7 to be turned to OFF to route DSI0 to the display panel
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c6 {
+	status = "disabled";
+};
+
+&lt9611_1v2 {
+	status = "disabled";
+};
+
+&lt9611_3v3 {
+	status = "disabled";
+};
+
+&vreg_bob_3v3 {
+	status = "disabled";
+};
+
+&lt9611_codec {
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "visionox,vtdr6130";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vddio-supply = <&vreg_l12b_1p8>;
+		vci-supply = <&vreg_l13b_3p0>;
+		vdd-supply = <&vreg_l11b_1p2>;
+
+		pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync_active>;
+		pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+
+	/*
+	 * DTC requires to have both endpoints when compiling the overlay
+	 * and also requires the #address/size-cells + reg properties
+	 */
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+
+			mdss_dsi0_out: endpoint {
+				remote-endpoint = <&panel0_in>;
+			};
+		};
+	};
+};
+
+&spi4 {
+	/* DTC requires the #address/size-cells to compile DTBO */
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	touchscreen@0 {
+		compatible = "goodix,gt9916";
+		reg = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <162 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 161 GPIO_ACTIVE_LOW>;
+
+		avdd-supply = <&vreg_l14b_3p2>;
+
+		spi-max-frequency = <1000000>;
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <2400>;
+
+		pinctrl-0 = <&ts_irq>, <&ts_reset>;
+		pinctrl-names = "default";
+	};
+};
+
+&tlmm {
+	disp0_reset_n_active: disp0-reset-n-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	disp0_reset_n_suspend: disp0-reset-n-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdp_vsync_active: mdp-vsync-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdp_vsync_suspend: mdp-vsync-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	ts_irq: ts-irq-state {
+		pins = "gpio161";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+		output-disable;
+	};
+
+	ts_reset: ts-reset-state {
+		pins = "gpio162";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+};

-- 
2.34.1