Re: [PATCH v2 2/2] arm64: dts: qcom: sa8295p: Enable tertiary controller and its 4 USB ports

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Feb 13, 2024 at 09:39:51AM +0100, Krzysztof Kozlowski wrote:
> On 13/02/2024 09:27, Krishna Kurapati wrote:
> > Multiport USB controller (host-only) of SA8295 ADP has 4 Type-A ports
> > exposed for connecting peripherals. The VBUS to these peripherals is
> > provided by TPS2559QWDRCTQ1 regulators connected to these ports. Each
> > regulator has an enable pin controlled by PMM8540. Since these regulators
> > are GPIO controlled regulators, model them as fixed regulators and keep
> > them Always-On at boot since we are wakeup capable and we don't need to
> > turn them off on suspend. Also since we don't enter device mode, these
> > regulators can be kept on.
> > 
> > Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 83 ++++++++++++++++++++++++
> >  1 file changed, 83 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > index fd253942e5e5..49418843c214 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > @@ -9,6 +9,7 @@
> >  #include <dt-bindings/gpio/gpio.h>
> >  #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> >  #include <dt-bindings/spmi/spmi.h>
> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> >  
> >  #include "sa8540p.dtsi"
> >  #include "sa8540p-pmics.dtsi"
> > @@ -108,6 +109,46 @@ edp3_connector_in: endpoint {
> >  			};
> >  		};
> >  	};
> > +
> > +	regulator-usb2-vbus {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "USB2_VBUS";
> > +		gpio = <&pmm8540c_gpios 9 GPIO_ACTIVE_HIGH>;
> > +		pinctrl-0 = <&usb2_en>;
> > +		pinctrl-names = "default";
> > +		enable-active-high;
> > +		regulator-always-on;
> > +	};
> > +
> > +	regulator-usb3-vbus {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "USB3_VBUS";
> > +		gpio = <&pmm8540e_gpios 5 GPIO_ACTIVE_HIGH>;
> > +		pinctrl-0 = <&usb3_en>;
> > +		pinctrl-names = "default";
> > +		enable-active-high;
> > +		regulator-always-on;
> > +	};
> > +
> > +	regulator-usb4-vbus {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "USB4_VBUS";
> > +		gpio = <&pmm8540g_gpios 5 GPIO_ACTIVE_HIGH>;
> > +		pinctrl-0 = <&usb4_en>;
> > +		pinctrl-names = "default";
> > +		enable-active-high;
> > +		regulator-always-on;
> > +	};
> > +
> > +	regulator-usb5-vbus {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "USB5_VBUS";
> > +		gpio = <&pmm8540g_gpios 9 GPIO_ACTIVE_HIGH>;
> > +		pinctrl-0 = <&usb5_en>;
> > +		pinctrl-names = "default";
> > +		enable-active-high;
> > +		regulator-always-on;
> 
> Why all these regulators are always on? If USB controller does not probe
> for any reason, why keeping them enabled? These must not be always-on,
> but instead used by connector as VBUS supply (or by whatever you have
> there for USB).
> 

I'm not too concerned about keeping the lights on in this scenario, but
if we can describe this properly let's do so (and let's do so on other
boards with connectors as well).

We'd have a set of usb-a-connector nodes, that we can tie to the nodes
in the USB/phy, and the supply. But so far we've associated a connector
with a port manager, here we don't have one of those, so where would the
node reside and who should acquire and drive the vbus-supply?

Regards,
Bjorn

> Best regards,
> Krzysztof
> 




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux