Hi Archit,
On Tue, 5 Jan 2016 10:55:01 +0530
Archit Taneja <architt@xxxxxxxxxxxxxx> wrote:
> Add DT bindings document for the Qualcomm NAND controller driver.
>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: Rob Herring <robh@xxxxxxxxxx>
> Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
> ---
> v5:
> - Make changes to incorporate chip select sub nodes (brcmnand taken as
> reference)
>
> v3:
> - Don't use '0x' when specifying nand controller address space
> - Add optional property for on-flash bbt usage
>
> .../devicetree/bindings/mtd/qcom_nandc.txt | 84 ++++++++++++++++++++++
> 1 file changed, 84 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/qcom_nandc.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> new file mode 100644
> index 0000000..b2cf2d9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> @@ -0,0 +1,84 @@
> +* Qualcomm NAND controller
> +
> +Required properties:
> +- compatible: should be "qcom,ebi2-nand" for IPQ806x
> +- reg: MMIO address range
> +- clocks: must contain core clock and always on clock
> +- clock-names: must contain "core" for the core clock and "aon" for the
> + always on clock
> +- dmas: DMA specifier, consisting of a phandle to the ADM DMA
> + controller node and the channel number to be used for
> + NAND. Refer to dma.txt and qcom_adm.txt for more details
> +- dma-names: must be "rxtx"
> +- qcom,cmd-crci: must contain the ADM command type CRCI block instance
> + number specified for the NAND controller on the given
> + platform
> +- qcom,data-crci: must contain the ADM data type CRCI block instance
> + number specified for the NAND controller on the given
> + platform
> +- #address-cells: <1> - subnodes give the chip-select number
> +- #size-cells: <0>
> +
> +* NAND chip-select
> +
> +Each controller may contain one or more subnodes to represent enabled
> +chip-selects which (may) contain NAND flash chips. Their properties are as
> +follows.
> +
> +Required properties:
> +- compatible: should contain "qcom,nandcs"
> +- reg: a single integer representing the chip-select
> + number (e.g., 0, 1, 2, etc.)
> +- #address-cells: see partition.txt
> +- #size-cells: see partition.txt
> +- nand-ecc-strength: number of bits to correct per ECC step. Must be 4 or 8
> + bits.
> +- nand-ecc-step-size: bytes of data per ECC step. Must be 512.
> +
> +Optional properties:
> +- nand-bus-width: bus width. Must be 8 or 16. If not present, 8 is chosen
> + as default
You should probably reference
Documentation/devicetree/bindings/mtd/nand.txt which is documenting
generic nand-xxx properties.
> +
> +Each nandcs device node may optionally contain sub-nodes describing the flash
> +partition mapping. See partition.txt for more detail.
> +
> +Example:
> +
> +nand@1ac00000 {
> + compatible = "qcom,ebi2-nandc";
> + reg = <0x1ac00000 0x800>;
> +
> + clocks = <&gcc EBI2_CLK>,
> + <&gcc EBI2_AON_CLK>;
> + clock-names = "core", "aon";
> +
> + dmas = <&adm_dma 3>;
> + dma-names = "rxtx";
> + qcom,cmd-crci = <15>;
> + qcom,data-crci = <3>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + nandcs@0 {
> + compatible = "qcom,nandcs";
> + reg = <0>;
> +
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> + nand-bus-width = <8>;
> +
It's now recommended to define a 'partitions' subnode to store those
partition nodes.
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "boot-nand";
> + reg = <0 0x58a0000>;
> + };
> +
> + partition@58a0000 {
> + label = "fs-nand";
> + reg = <0x58a0000 0x4000000>;
> + };
> + };
> +};
The rest looks good to me.
Reviewed-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
Best Regards,
Boris
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
