Document Qcom QCA807x PHY package. Qualcomm QCA807X Ethernet PHY is PHY package of 2 or 5 IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. Document the required property to make the PHY package correctly configure and work. Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx> Reviewed-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx> --- .../devicetree/bindings/net/qcom,qca807x.yaml | 184 ++++++++++++++++++ 1 file changed, 184 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/qcom,qca807x.yaml diff --git a/Documentation/devicetree/bindings/net/qcom,qca807x.yaml b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml new file mode 100644 index 000000000000..7290024024f5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,qca807x.yaml @@ -0,0 +1,184 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qcom,qca807x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QCA807x Ethernet PHY + +maintainers: + - Christian Marangi <ansuelsmth@xxxxxxxxx> + - Robert Marko <robert.marko@xxxxxxxxxx> + +description: | + Qualcomm QCA8072/5 Ethernet PHY is PHY package of 2 or 5 + IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and + 1000BASE-T PHY-s. + + They feature 2 SerDes, one for PSGMII or QSGMII connection with + MAC, while second one is SGMII for connection to MAC or fiber. + + Both models have a combo port that supports 1000BASE-X and + 100BASE-FX fiber. + + Each PHY inside of QCA807x series has 4 digitally controlled + output only pins that natively drive LED-s for up to 2 attached + LEDs. Some vendor also use these 4 output for GPIO usage without + attaching LEDs. + + Note that output pins can be set to drive LEDs OR GPIO, mixed + definition are not accepted. + +$ref: ethernet-phy-package.yaml# + +properties: + compatible: + enum: + - qcom,qca8072-package + - qcom,qca8075-package + + qcom,package-mode: + description: | + PHY package can be configured in 3 mode following this table: + + First Serdes mode Second Serdes mode + Option 1 PSGMII for copper Disabled + ports 0-4 + Option 2 PSGMII for copper 1000BASE-X / 100BASE-FX + ports 0-4 + Option 3 QSGMII for copper SGMII for + ports 0-3 copper port 4 + + PSGMII mode (option 1 or 2) is configured dynamically based on + the presence of a connected SFP device. + $ref: /schemas/types.yaml#/definitions/string + enum: + - qsgmii + - psgmii + default: psgmii + + qcom,tx-drive-strength-milliwatt: + description: set the TX Amplifier value in mv. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [140, 160, 180, 200, 220, + 240, 260, 280, 300, 320, + 400, 500, 600] + default: 600 + +patternProperties: + ^ethernet-phy@[a-f0-9]+$: + $ref: ethernet-phy.yaml# + + properties: + qcom,dac-full-amplitude: + description: + Set Analog MDI driver amplitude to FULL. + + With this not defined, amplitude is set to DSP. + (amplitude is adjusted based on cable length) + + With this enabled and qcom,dac-full-bias-current + and qcom,dac-disable-bias-current-tweak disabled, + bias current is half. + type: boolean + + qcom,dac-full-bias-current: + description: + Set Analog MDI driver bias current to FULL. + + With this not defined, bias current is set to DSP. + (bias current is adjusted based on cable length) + + Actual bias current might be different with + qcom,dac-disable-bias-current-tweak disabled. + type: boolean + + qcom,dac-disable-bias-current-tweak: + description: | + Set Analog MDI driver bias current to disable tweak + to bias current. + + With this not defined, bias current tweak are enabled + by default. + + With this enabled the following tweak are NOT applied: + - With both FULL amplitude and FULL bias current: bias current + is set to half. + - With only DSP amplitude: bias current is set to half and + is set to 1/4 with cable < 10m. + - With DSP bias current (included both DSP amplitude and + DSP bias current): bias current is half the detected current + with cable < 10m. + type: boolean + + gpio-controller: true + + '#gpio-cells': + const: 2 + + if: + required: + - gpio-controller + then: + properties: + leds: false + + unevaluatedProperties: false + +required: + - compatible + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/leds/common.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy-package@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,qca8075-package"; + reg = <0>; + + qcom,package-mode = "qsgmii"; + + ethernet-phy@0 { + reg = <0>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + }; + }; + + ethernet-phy@1 { + reg = <1>; + }; + + ethernet-phy@2 { + reg = <2>; + + gpio-controller; + #gpio-cells = <2>; + }; + + ethernet-phy@3 { + reg = <3>; + }; + + ethernet-phy@4 { + reg = <4>; + }; + }; + }; -- 2.43.0
