Re: [net-next PATCH v5 1/9] dt-bindings: net: document ethernet PHY package nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Feb 02, 2024 at 02:52:59PM -0600, Rob Herring wrote:
> On Thu, Feb 01, 2024 at 04:17:27PM +0100, Christian Marangi wrote:
> > Document ethernet PHY package nodes used to describe PHY shipped in
> > bundle of 2-5 PHY. The special node describe a container of PHY that
> > share common properties. This is a generic schema and PHY package
> > should create specialized version with the required additional shared
> > properties.
> > 
> > Example are PHY packages that have some regs only in one PHY of the
> > package and will affect every other PHY in the package, for example
> > related to PHY interface mode calibration or global PHY mode selection.
> > 
> > The PHY package node MUST declare the base address used by the PHY driver
> > for global configuration by calculating the offsets of the global PHY
> > based on the base address of the PHY package.
> > 
> > Each reg of the PHYs defined in the PHY Package node is an offset of the
> > PHY Package reg.
> > 
> > Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> > ---
> >  .../bindings/net/ethernet-phy-package.yaml    | 55 +++++++++++++++++++
> >  1 file changed, 55 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml b/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> > new file mode 100644
> > index 000000000000..d7cdbb1a4b3e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/ethernet-phy-package.yaml
> > @@ -0,0 +1,55 @@
> > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/ethernet-phy-package.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Ethernet PHY Package Common Properties
> > +
> > +maintainers:
> > +  - Christian Marangi <ansuelsmth@xxxxxxxxx>
> > +
> > +description:
> > +  PHY packages are multi-port Ethernet PHY of the same family
> > +  and each Ethernet PHY is affected by the global configuration
> > +  of the PHY package.
> > +
> > +  Each reg of the PHYs defined in the PHY Package node is
> > +  an offset of the PHY Package reg.
> > +
> > +  Each Ethernet PHYs defined in the PHY package node is
> > +  reachable in the MDIO bus at the address of the PHY
> > +  Package offset of the Ethernet PHY reg.
> 
> If the phys are addressed with an MDIO address, then just use those.
>

Thanks a lot for the review Rob.

Just to make sure I got this right!

Are you ok to have the PHYs with absolute reg? (it would make thing soo
much easy)

It would result in this node example on real world scenario.

	ethernet-phy-package@16 {
		compatible = "qcom,qca8075-package";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <16>;
		qcom,package-mode = "qsgmii";

		qca8075_16: ethernet-phy@16 {
			compatible = "ethernet-phy-ieee802.3-c22";
			reg = <16>;
		};

		qca8075_17: ethernet-phy@17 {
			compatible = "ethernet-phy-ieee802.3-c22";
			reg = <17>;
		};

		qca8075_18: ethernet-phy@18 {
			compatible = "ethernet-phy-ieee802.3-c22";
			reg = <18>;
		};

		qca8075_19: ethernet-phy@19 {
			compatible = "ethernet-phy-ieee802.3-c22";
			reg = <19>;
		};
	};

> > +
> > +properties:
> > +  $nodename:
> > +    pattern: "^ethernet-phy-package(@[a-f0-9]+)?$"
> 
> Can't be optional if 'reg' is required (which it should be).
> 
> > +
> > +  reg:
> > +    minimum: 0
> > +    maximum: 31
> > +    description:
> > +      The base ID number for the PHY package.
> > +      Commonly the ID of the first PHY in the PHY package.
> > +
> > +      Some PHY in the PHY package might be not defined but
> > +      still occupy ID on the device (just not attached to
> > +      anything) hence the PHY package reg might correspond
> > +      to a not attached PHY (offset 0).
> > +
> > +  '#address-cells':
> > +    const: 1
> > +
> > +  '#size-cells':
> > +    const: 0
> > +
> > +patternProperties:
> > +  ^ethernet-phy(@[a-f0-9]+)?$:
> 
> Same issue here.
> 
> > +    $ref: ethernet-phy.yaml#
> > +
> > +required:
> > +  - reg
> > +  - '#address-cells'
> > +  - '#size-cells'
> > +
> > +additionalProperties: true
> > -- 
> > 2.43.0
> > 

-- 
	Ansuel




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux