Re: [PATCH 13/13] arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 13.01.2024 06:42, Dmitry Baryshkov wrote:
> Plug in USB-C related bits and pieces to enable USB role switching and
> USB-C orientation handling for the Qualcomm RB2 board.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 62 ++++++++++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sm6115.dtsi     | 38 ++++++++++++++++++++
>  2 files changed, 100 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> index 52f31f3166c2..a96e3afb65bc 100644
> --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> @@ -6,8 +6,10 @@
>  /dts-v1/;
>  
>  #include <dt-bindings/leds/common.h>
> +#include <dt-bindings/usb/pd.h>
>  #include "sm4250.dtsi"
>  #include "pm6125.dtsi"
> +#include "pmi632.dtsi"
>  
>  / {
>  	model = "Qualcomm Technologies, Inc. QRB4210 RB2";
> @@ -256,6 +258,53 @@ kypd_vol_up_n: kypd-vol-up-n-state {
>  	};
>  };
>  
> +&pmi632_typec {
> +	status = "okay";
> +
> +	connector {
> +		compatible = "usb-c-connector";
> +
> +		power-role = "dual";
> +		data-role = "dual";
> +		self-powered;
> +
> +		source-pdos = <PDO_FIXED(5000, 3000,
> +					 PDO_FIXED_DUAL_ROLE |
> +					 PDO_FIXED_USB_COMM |
> +					 PDO_FIXED_DATA_SWAP)>;
> +		sink-pdos = <PDO_FIXED(5000, 500,
> +					 PDO_FIXED_DUAL_ROLE |
> +					 PDO_FIXED_USB_COMM |
> +					 PDO_FIXED_DATA_SWAP)>;
> +		op-sink-microwatt = <10000000>;
So RB2 can provide 15 watts over the USB-C port, consume 2.5 but
requires 10? That doesn't make a whole lot of sense..

Unless I'm reading this wrong..

> +&usb_dwc3 {
> +	usb-role-switch;

Since this is a dual-role controller, I think this could live in the SoC
DT

> +};
> +
> +&usb_dwc3_hs {
> +	remote-endpoint = <&pmi632_hs_in>;
> +};
> +
>  &usb_hsphy {
>  	vdd-supply = <&vreg_l4a_0p9>;
>  	vdda-pll-supply = <&vreg_l12a_1p8>;
> @@ -618,10 +675,15 @@ &usb_hsphy {
>  &usb_qmpphy {
>  	vdda-phy-supply = <&vreg_l4a_0p9>;
>  	vdda-pll-supply = <&vreg_l12a_1p8>;
> +	orientation-switch;

Similarly, if this doesn't kaboom w/ our implementation too much, the
PHY itself has orientation detection capabilities

Konrad




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux