Re: [PATCH v6 6/6] PCI: qcom: Add OPP support to scale performance state of power domain

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 12 Jan 2024 at 16:25, Krishna chaitanya chundru
<quic_krichai@xxxxxxxxxxx> wrote:
>
> QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
> maintains hardware state of a regulator by performing max aggregation of
> the requests made by all of the processors.
>
> PCIe controller can operate on different RPMh performance state of power
> domain based up on the speed of the link. And this performance state varies
> from target to target.
>
> It is manadate to scale the performance state based up on the PCIe speed
> link operates so that SoC can run under optimum power conditions.
>
> Add Operating Performance Points(OPP) support to vote for RPMh state based
> upon GEN speed link is operating.
>
> OPP can handle ICC bw voting also, so move icc bw voting through opp
> framework if opp entries are present.
>
> In PCIe certain gen speeds like GEN1x2 & GEN2X1 or GEN3x2 & GEN4x1 use
> same icc bw and has frequency, so use frequency based search to reduce
> number of entries in the opp table.
>
> Don't initialize icc if opp is supported.
>
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 83 ++++++++++++++++++++++++++++------
>  1 file changed, 70 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 035953f0b6d8..31512dc9d6ff 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -22,6 +22,7 @@
>  #include <linux/of.h>
>  #include <linux/of_gpio.h>
>  #include <linux/pci.h>
> +#include <linux/pm_opp.h>
>  #include <linux/pm_runtime.h>
>  #include <linux/platform_device.h>
>  #include <linux/phy/pcie.h>
> @@ -244,6 +245,7 @@ struct qcom_pcie {
>         const struct qcom_pcie_cfg *cfg;
>         struct dentry *debugfs;
>         bool suspended;
> +       bool opp_supported;
>  };
>
>  #define to_qcom_pcie(x)                dev_get_drvdata((x)->dev)
> @@ -1404,16 +1406,14 @@ static int qcom_pcie_icc_init(struct qcom_pcie *pcie)
>         return 0;
>  }
>
> -static void qcom_pcie_icc_update(struct qcom_pcie *pcie)
> +static void qcom_pcie_icc_opp_update(struct qcom_pcie *pcie)
>  {
>         struct dw_pcie *pci = pcie->pci;
> -       u32 offset, status;
> +       u32 offset, status, freq;
> +       struct dev_pm_opp *opp;
>         int speed, width;
>         int ret;
>
> -       if (!pcie->icc_mem)
> -               return;
> -
>         offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>         status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
>
> @@ -1424,11 +1424,42 @@ static void qcom_pcie_icc_update(struct qcom_pcie *pcie)
>         speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
>         width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
>
> -       ret = icc_set_bw(pcie->icc_mem, 0, width * QCOM_PCIE_LINK_SPEED_TO_BW(speed));
> -       if (ret) {
> -               dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> -                       ret);
> +       if (pcie->opp_supported) {
> +               switch (speed) {
> +               case 1:
> +                       freq = 2500000;
> +                       break;
> +               case 2:
> +                       freq = 5000000;
> +                       break;
> +               case 3:
> +                       freq = 8000000;
> +                       break;
> +               default:
> +                       WARN_ON_ONCE(1);
> +                       fallthrough;
> +               case 4:
> +                       freq = 16000000;

I expected that this kind of detail goes to the OPP table itself. Can
we index the table using the generation instead of frequency?

> +                       break;
> +               }
> +
> +               opp = dev_pm_opp_find_freq_exact(pci->dev, freq * width, true);
> +               if (!IS_ERR(opp)) {
> +                       ret = dev_pm_opp_set_opp(pci->dev, opp);
> +                       if (ret)
> +                               dev_err(pci->dev, "Failed to set opp: freq %ld ret %d\n",
> +                                       dev_pm_opp_get_freq(opp), ret);
> +                       dev_pm_opp_put(opp);
> +               }
> +       } else {
> +               ret = icc_set_bw(pcie->icc_mem, 0, width * QCOM_PCIE_LINK_SPEED_TO_BW(speed));
> +               if (ret) {
> +                       dev_err(pci->dev, "failed to set interconnect bandwidth for pcie-mem: %d\n",
> +                               ret);
> +               }
>         }
> +
> +       return;
>  }
>
>  static int qcom_pcie_link_transition_count(struct seq_file *s, void *data)
> @@ -1471,8 +1502,10 @@ static void qcom_pcie_init_debugfs(struct qcom_pcie *pcie)
>  static int qcom_pcie_probe(struct platform_device *pdev)
>  {
>         const struct qcom_pcie_cfg *pcie_cfg;
> +       unsigned long max_freq = INT_MAX;
>         struct device *dev = &pdev->dev;
>         struct qcom_pcie *pcie;
> +       struct dev_pm_opp *opp;
>         struct dw_pcie_rp *pp;
>         struct resource *res;
>         struct dw_pcie *pci;
> @@ -1539,9 +1572,33 @@ static int qcom_pcie_probe(struct platform_device *pdev)
>                 goto err_pm_runtime_put;
>         }
>
> -       ret = qcom_pcie_icc_init(pcie);
> -       if (ret)
> +        /* OPP table is optional */
> +       ret = devm_pm_opp_of_add_table(dev);
> +       if (ret && ret != -ENODEV) {
> +               dev_err_probe(dev, ret, "Failed to add OPP table\n");
>                 goto err_pm_runtime_put;
> +       }

Can we initialise the table from the driver if it is not found? This
will help us by having the common code later on.

> +
> +       /* vote for max freq in the opp table if opp table is present */
> +       if (ret != -ENODEV) {
> +               opp = dev_pm_opp_find_freq_floor(dev, &max_freq);
> +               if (!IS_ERR(opp)) {
> +                       ret = dev_pm_opp_set_opp(dev, opp);
> +                       if (ret)
> +                               dev_err_probe(pci->dev, ret,
> +                                             "Failed to set opp: freq %ld\n",
> +                                             dev_pm_opp_get_freq(opp));
> +                       dev_pm_opp_put(opp);
> +               }
> +               pcie->opp_supported = true;
> +       }
> +
> +       /* Skip icc init if opp is supported as icc bw vote is handled by opp framework */
> +       if (!pcie->opp_supported) {
> +               ret = qcom_pcie_icc_init(pcie);
> +               if (ret)
> +                       goto err_pm_runtime_put;
> +       }
>
>         ret = pcie->cfg->ops->get_resources(pcie);
>         if (ret)
> @@ -1561,7 +1618,7 @@ static int qcom_pcie_probe(struct platform_device *pdev)
>                 goto err_phy_exit;
>         }
>
> -       qcom_pcie_icc_update(pcie);
> +       qcom_pcie_icc_opp_update(pcie);
>
>         if (pcie->mhi)
>                 qcom_pcie_init_debugfs(pcie);
> @@ -1640,7 +1697,7 @@ static int qcom_pcie_resume_noirq(struct device *dev)
>                 pcie->suspended = false;
>         }
>
> -       qcom_pcie_icc_update(pcie);
> +       qcom_pcie_icc_opp_update(pcie);
>
>         return 0;
>  }
>
> --
> 2.42.0
>
>


-- 
With best wishes
Dmitry




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux