To determine the max_timeout value, the below calculation is used.
max_timeout = 0x10000000 / clk_rate
cat /sys/devices/platform/soc@0/b017000.watchdog/watchdog/watchdog0/max_timeout
8388
However, this is not valid for all the platforms. IPQ SoCs starting from
IPQ40xx and recent Snapdragron SoCs also has the bark and bite time field
length of 20bits, which can hold max up to 32 seconds if the clk_rate is
32KHz.
If the user tries to configure the timeout more than 32s, then the value
will be truncated and the actual value will not be reflected in the HW.
To avoid this, lets add a variable called max_tick_count in the device data,
which defines max counter value of the WDT controller. Using this, max-timeout
will be calculated in runtime for various WDT contorllers.
With this change, we get the proper max_timeout as below and restricts
the user from configuring the timeout higher than this.
cat /sys/devices/platform/soc@0/b017000.watchdog/watchdog/watchdog0/max_timeout
32
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx>
---
drivers/watchdog/qcom-wdt.c | 13 ++++++++-----
1 file changed, 8 insertions(+), 5 deletions(-)
diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
index 9e790f0c2096..83fc3e3abb03 100644
--- a/drivers/watchdog/qcom-wdt.c
+++ b/drivers/watchdog/qcom-wdt.c
@@ -41,6 +41,7 @@ static const u32 reg_offset_data_kpss[] = {
struct qcom_wdt_match_data {
const u32 *offset;
bool pretimeout;
+ u32 max_tick_count;
};
struct qcom_wdt {
@@ -177,11 +178,13 @@ static const struct watchdog_info qcom_wdt_pt_info = {
static const struct qcom_wdt_match_data match_data_apcs_tmr = {
.offset = reg_offset_data_apcs_tmr,
.pretimeout = false,
+ .max_tick_count = 0x10000000U,
};
static const struct qcom_wdt_match_data match_data_kpss = {
.offset = reg_offset_data_kpss,
.pretimeout = true,
+ .max_tick_count = 0xFFFFFU,
};
static int qcom_wdt_probe(struct platform_device *pdev)
@@ -236,7 +239,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
*/
wdt->rate = clk_get_rate(clk);
if (wdt->rate == 0 ||
- wdt->rate > 0x10000000U) {
+ wdt->rate > data->max_tick_count) {
dev_err(dev, "invalid clock rate\n");
return -EINVAL;
}
@@ -260,7 +263,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
wdt->wdd.ops = &qcom_wdt_ops;
wdt->wdd.min_timeout = 1;
- wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
+ wdt->wdd.max_timeout = data->max_tick_count / wdt->rate;
wdt->wdd.parent = dev;
wdt->layout = data->offset;
@@ -268,11 +271,11 @@ static int qcom_wdt_probe(struct platform_device *pdev)
wdt->wdd.bootstatus = WDIOF_CARDRESET;
/*
- * If 'timeout-sec' unspecified in devicetree, assume a 30 second
- * default, unless the max timeout is less than 30 seconds, then use
+ * If 'timeout-sec' unspecified in devicetree, assume a 32 second
+ * default, unless the max timeout is less than 32 seconds, then use
* the max instead.
*/
- wdt->wdd.timeout = min(wdt->wdd.max_timeout, 30U);
+ wdt->wdd.timeout = min(wdt->wdd.max_timeout, 32U);
watchdog_init_timeout(&wdt->wdd, 0, dev);
/*
---
base-commit: 9e21984d62c56a0f6d1fc6f76b646212cfd7fe88
change-id: 20240111-wdt-5bd079ecf14d
Best regards,
--
Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx>
