Re: [PATCH V3 2/2] arm64: dts: qcom: sc7280: add QCrypto nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu Dec 14, 2023 at 11:36 AM CET, Om Prakash Singh wrote:
> Add the QCE and Crypto BAM DMA nodes.
>
> Signed-off-by: Om Prakash Singh <quic_omprsing@xxxxxxxxxxx>
> ---
>
> Changes in V3:
>   - V2 patch was sent without actual modification. Resending the patch with modified file.
>
> Changes in V2:
>   - Update DT node sequence as per register ascending order.
>   - Fix DT node properties as per convention.
>
>  arch/arm64/boot/dts/qcom/sc7280.dtsi | 22 ++++++++++++++++++++++
>  1 file changed, 22 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 66f1eb83cca7..b819724c1255 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -2233,6 +2233,28 @@ pcie1_phy: phy@1c0e000 {
>  			status = "disabled";
>  		};
>  
> +		cryptobam: dma-controller@1dc4000 {
> +			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
> +			reg = <0x0 0x01dc4000 0x0 0x28000>;
> +			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
> +			#dma-cells = <1>;
> +			iommus = <&apps_smmu 0x4e4 0x0011>,
> +				 <&apps_smmu 0x4e6 0x0011>;
> +			qcom,ee = <0>;
> +			qcom,controlled-remotely;
> +		};

Hi,

Unfortunately I seem to have boot failure / device crash with cryptobam
enabled on my qcm6490-fairphone-fp5. Are you aware of any firmware
differences that could cause this with QCM6490 LA firmware?

Looking at downstream msm-5.4 dmesg I do see this BAM being used so it
should generally be accessible from Linux.

[    5.217214] qce 1de0000.qcedev: Adding to iommu group 18
[    5.223741] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[    5.234986] qce 1de0000.qcedev: QTI Crypto 5.6.0 device found @0x1de0000
[    5.242981] sps_register_bam_device: sps:BAM 0x0000000001dc4000 is registered
[    5.251124] sps_bam_enable: sps:BAM 0x0000000001dc4000 (va:0x000000001db63156) enabled: ver:0x27, number of pipes:16
[    5.262783] QCE50: qce_sps_init:  QTI MSM CE-BAM at 0x0000000001dc4000 irq 9
[    5.271820] qce 1de0000.qcedev:qcom_cedev_ns_cb: Adding to iommu group 19
[    5.281083] qce 1de0000.qcedev:qcom_cedev_s_cb: Adding to iommu group 20
[    5.289376] qcrypto 1de0000.qcrypto: Adding to iommu group 21
[    5.296326] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[    5.307675] qcrypto 1de0000.qcrypto: QTI Crypto 5.6.0 device found @0x1de0000
[    5.315867] QCE50: qce_sps_init:  QTI MSM CE-BAM at 0x0000000001dc4000 irq 9

Any idea?

Regards
Luca

> +
> +		crypto: crypto@1dfa000 {
> +			compatible = "qcom,sc7280-qce", "qcom,sm8150-qce", "qcom,qce";
> +			reg = <0x0 0x01dfa000 0x0 0x6000>;
> +			dmas = <&cryptobam 4>, <&cryptobam 5>;
> +			dma-names = "rx", "tx";
> +			iommus = <&apps_smmu 0x4e4 0x0011>,
> +				 <&apps_smmu 0x4e4 0x0011>;
> +			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
> +			interconnect-names = "memory";
> +		};
> +
>  		ipa: ipa@1e40000 {
>  			compatible = "qcom,sc7280-ipa";
>  






[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux