Re: [RFC PATCH 03/10] drm/mipi-dsi: add API for manual control over the DSI link power state

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> DSI device lifetime has three different stages:
> 1. before the DSI link being powered up and clocking,
> 2. when the DSI link is in LP state (for the purpose of this question,
> this is the time between the DSI link being powered up and the video
> stream start)
> 3. when the DSI link is in HS state (while streaming the video).

It's not clear to me what (2) is. What is the state of the clock and
data lanes?

Clk an Data0 should be in the LP mode, ready for LP Data Transfer.

Then this is somehow missing
https://docs.kernel.org/gpu/drm-kms-helpers.html#mipi-dsi-bridge-operation

A DSI host should keep the PHY powered down until the pre_enable operation is called. All lanes are in an undefined idle state up to this point, and it must not be assumed that it is LP-11. pre_enable should initialise the PHY, set the data lanes to LP-11, and the clock lane to either LP-11 or HS
  depending on the mode_flag MIPI_DSI_CLOCK_NON_CONTINUOUS.

So I don't think these three states are sufficient, see below, that there
should be at least four.

-michael


I don't think we support ULPS currently.



I'm facing similar issues with the tc358775 bridge. This bridge needs
to release its reset while both clock and data lanes are in LP-11 mode.
But then it needs to be configured (via I2C) while the clock lane is
in enabled (HS mode), but the data lanes are still in LP-11 mode.

To me it looks like there is a fouth case then:
1. unpowered
2. DSI clock and data are in LP-11
3. DSI clock is in HS and data are in LP-11
4. DSI clock is in HS and data is in HS

(And of course the bridge needs continuous clock mode).

> Different DSI bridges have different requirements with respect to the
> code being executed at stages 1 and 2. For example several DSI-to-eDP
> bridges (ps8640, tc358767 require for the link to be quiet during
> reset time.
> The DSI-controlled bridges and DSI panels need to send some commands
> in stage 2, before starting up video
>
> In the DRM subsystem stage 3 naturally maps to the
> drm_bridge_funcs::enable, stage 1 also naturally maps to the
> drm_bridge_funcs::pre_enable. Stage 2 doesn't have its own place in
> the DRM call chain.
> Earlier we attempted to solve that using the pre_enable_prev_first,
> which remapped pre-enable callback execution order. However it has led
> us to the two issues. First, at the DSI host driver we do not know
> whether the panel / bridge were updated to use pre_enable_prev_first
> or not. Second, if the bridge has to perform steps during both stages
> 1 and 2, it can not do that.
>
> I'm trying to find a way to express the difference between stages 1
> and 2 in the generic code, so that we do not to worry about particular
> DSI host and DSI bridge / panel peculiarities when implementing the
> DSI host and/or DSI panel driver.

For now, I have a rather hacky ".dsi_lp11_notify" callback in
drm_bridge_funcs which is supposed to be called by the DSI host while the clock and data lanes are in LP-11 mode. But that is rather an RFC and me needing something to get the driver for this bridge working. Because it's
badly broken. FWIW, you can find my work-in-progress patches at
https://github.com/mwalle/linux/tree/feature-tc358775-fixes

-michael



--
With best wishes
Dmitry




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux