Re: [net-next PATCH RFC v3 5/8] dt-bindings: net: add QCA807x PHY defines

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Nov 26, 2023 at 02:53:43AM +0100, Christian Marangi wrote:
> From: Robert Marko <robert.marko@xxxxxxxxxx>
> 
> Add DT bindings defined for Qualcomm QCA807x PHY series related to
> calibration and DAC settings.
> 
> Signed-off-by: Robert Marko <robert.marko@xxxxxxxxxx>
> Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> ---
>  include/dt-bindings/net/qcom-qca807x.h | 30 ++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
>  create mode 100644 include/dt-bindings/net/qcom-qca807x.h

How is this used? There's nothing in the binding about it. Binding 
headers go with the binding schema that define how they are used.

> 
> diff --git a/include/dt-bindings/net/qcom-qca807x.h b/include/dt-bindings/net/qcom-qca807x.h
> new file mode 100644
> index 000000000000..e7d4d09b7dd4
> --- /dev/null
> +++ b/include/dt-bindings/net/qcom-qca807x.h
> @@ -0,0 +1,30 @@
> +/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
> +/*
> + * Device Tree constants for the Qualcomm QCA807X PHYs
> + */
> +
> +#ifndef _DT_BINDINGS_QCOM_QCA807X_H
> +#define _DT_BINDINGS_QCOM_QCA807X_H
> +
> +/* Full amplitude, full bias current */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_BIAS		0
> +/* Amplitude follow DSP (amplitude is adjusted based on cable length), half bias current */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS		1
> +/* Full amplitude, bias current follow DSP (bias current is adjusted based on cable length) */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_DSP_BIAS		2
> +/* Both amplitude and bias current follow DSP */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_BIAS		3
> +/* Full amplitude, half bias current */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS		4
> +/* Amplitude follow DSP setting; 1/4 bias current when cable<10m,
> + * otherwise half bias current
> + */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS	5
> +/* Full amplitude; same bias current setting with “010” and “011”,
> + * but half more bias is reduced when cable <10m
> + */
> +#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS_SHORT	6
> +/* Amplitude follow DSP; same bias current setting with “110”, default value */
> +#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS_SHORT	7
> +
> +#endif
> -- 
> 2.40.1
> 




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux