On 15/11/2023 09:55, Legale Legale wrote:
Add node to support this bus inside of IPQ6018.
For example, this bus is used to work with the
voltage regulator (mp5496) on the Yuncore AX840 wireless AP.
Signed-off-by: Isaev Ruslan <legale.legale@xxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index e59b9df96c7e..745bfc6e2907 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -507,6 +507,21 @@ blsp1_i2c3: i2c@78b7000 {
status = "disabled";
};
+ blsp1_i2c6: i2c@78ba000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x078ba000 0x600>;
reg = <0x0 0x078ba000 0x0 0x600>;
like the other regs here
+ interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ clock-frequency = <100000>;
Why not <400000>; as with other nodes ?
+ dmas = <&blsp_dma 22>, <&blsp_dma 23>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
qpic_bam: dma-controller@7984000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x07984000 0x0 0x1a000>;
--
2.42.0
What tree does this apply to ?
git checkout -b linux-next-6.7-rc1 v6.7-rc1
Switched to a new branch 'linux-next-6.7-rc1'
deckard@sagittarius-a:~/Development/qualcomm/qlt-kernel$ b4 shazam
CACDmYyf4hxbuw+cpKqEDnqmHpS9yPXuE5MPD5_XZ3hjmYuViUQ@xxxxxxxxxxxxxx
Grabbing thread from
lore.kernel.org/all/CACDmYyf4hxbuw%2BcpKqEDnqmHpS9yPXuE5MPD5_XZ3hjmYuViUQ@xxxxxxxxxxxxxx/t.mbox.gz
Checking for newer revisions
Grabbing search results from lore.kernel.org
Analyzing 1 messages in the thread
Checking attestation on all messages, may take a moment...
---
[PATCH] arm64: dts: qcom: ipq6018: add QUP5 I2C node
---
NOTE: install dkimpy for DKIM signature verification
---
Total patches: 1
---
Applying: arm64: dts: qcom: ipq6018: add QUP5 I2C node
Patch failed at 0001 arm64: dts: qcom: ipq6018: add QUP5 I2C node
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".
error: git diff header lacks filename information when removing 1
leading pathname component (line 6)
hint: Use 'git am --show-current-patch=diff' to see the failed patch
---
bod
