Re: [PATCH v2 4/7] scsi: ufs: ufs-qcom: Limit HS-G5 Rate-A to hosts with HW version 5

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Nov 06, 2023 at 08:46:10PM -0800, Can Guo wrote:
> From: Can Guo <quic_cang@xxxxxxxxxxx>
> 
> Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
> HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
> to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
> 
> Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
> ---
>  drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
>  1 file changed, 17 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 60b35ca..55ee31d 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -442,9 +442,25 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
>  static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +	struct ufs_host_params *host_params = &host->host_params;
>  	struct phy *phy = host->generic_phy;
> +	enum phy_mode mode;
>  	int ret;
>  
> +	/*
> +	 * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.

Does this limitation apply to future targets as well or just to SM8550? If
it's the latter, then we need to use a flag.

- Mani

> +	 * If the HS-G5 PHY gear is used, update host_params->hs_rate to Rate-A,
> +	 * so that the subsequent power mode change shall stick to Rate-A.
> +	 */
> +	if (host->hw_ver.major == 0x5) {
> +		if (host->phy_gear == UFS_HS_G5)
> +			host_params->hs_rate = PA_HS_MODE_A;
> +		else
> +			host_params->hs_rate = PA_HS_MODE_B;
> +	}
> +
> +	mode = host_params->hs_rate == PA_HS_MODE_B ? PHY_MODE_UFS_HS_B : PHY_MODE_UFS_HS_A;
> +
>  	/* Reset UFS Host Controller and PHY */
>  	ret = ufs_qcom_host_reset(hba);
>  	if (ret)
> @@ -459,7 +475,7 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
>  		return ret;
>  	}
>  
> -	phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);
> +	phy_set_mode_ext(phy, mode, host->phy_gear);
>  
>  	/* power on phy - start serdes and phy's power and clocks */
>  	ret = phy_power_on(phy);
> -- 
> 2.7.4
> 

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux