DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
---
drivers/gpu/drm/msm/Kconfig | 8 +
drivers/gpu/drm/msm/Makefile | 1 +
drivers/gpu/drm/msm/dsi/dsi.h | 1 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 4 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 1 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c | 195 ++++++++++++++++++++++++
6 files changed, 210 insertions(+)
create mode 100644 drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c
diff --git a/drivers/gpu/drm/msm/Kconfig b/drivers/gpu/drm/msm/Kconfig
index 8e6c7c6..38a618e 100644
--- a/drivers/gpu/drm/msm/Kconfig
+++ b/drivers/gpu/drm/msm/Kconfig
@@ -68,3 +68,11 @@ config DRM_MSM_DSI_20NM_PHY
default y
help
Choose this option if the 20nm DSI PHY is used on the platform.
+
+config DRM_MSM_DSI_28NM_8960_PHY
+ bool "Enable DSI 28nm 8960 PHY driver in MSM DRM"
+ depends on DRM_MSM_DSI
+ default y
+ help
+ Choose this option if the 28nm DSI PHY 8960 variant is used on the
+ platform.
diff --git a/drivers/gpu/drm/msm/Makefile b/drivers/gpu/drm/msm/Makefile
index 0a543eb..96bcb66 100644
--- a/drivers/gpu/drm/msm/Makefile
+++ b/drivers/gpu/drm/msm/Makefile
@@ -62,6 +62,7 @@ msm-$(CONFIG_DRM_MSM_DSI) += dsi/dsi.o \
msm-$(CONFIG_DRM_MSM_DSI_28NM_PHY) += dsi/phy/dsi_phy_28nm.o
msm-$(CONFIG_DRM_MSM_DSI_20NM_PHY) += dsi/phy/dsi_phy_20nm.o
+msm-$(CONFIG_DRM_MSM_DSI_28NM_8960_PHY) += dsi/phy/dsi_phy_28nm_8960.o
ifeq ($(CONFIG_DRM_MSM_DSI_PLL),y)
msm-y += dsi/pll/dsi_pll.o
diff --git a/drivers/gpu/drm/msm/dsi/dsi.h b/drivers/gpu/drm/msm/dsi/dsi.h
index 5f5a373..8140e8b 100644
--- a/drivers/gpu/drm/msm/dsi/dsi.h
+++ b/drivers/gpu/drm/msm/dsi/dsi.h
@@ -31,6 +31,7 @@ enum msm_dsi_phy_type {
MSM_DSI_PHY_28NM_HPM,
MSM_DSI_PHY_28NM_LP,
MSM_DSI_PHY_20NM,
+ MSM_DSI_PHY_28NM_8960,
MSM_DSI_PHY_MAX
};
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
index 401ff58..d54e450 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -277,6 +277,10 @@ static const struct of_device_id dsi_phy_dt_match[] = {
{ .compatible = "qcom,dsi-phy-20nm",
.data = &dsi_phy_20nm_cfgs },
#endif
+#ifdef CONFIG_DRM_MSM_DSI_28NM_8960_PHY
+ { .compatible = "qcom,dsi-phy-28nm-8960",
+ .data = &dsi_phy_28nm_8960_cfgs },
+#endif
{}
};
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
index 0456b25..0d54ed0 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
@@ -43,6 +43,7 @@ struct msm_dsi_phy_cfg {
extern const struct msm_dsi_phy_cfg dsi_phy_28nm_hpm_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_28nm_lp_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_20nm_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_28nm_8960_cfgs;
struct msm_dsi_dphy_timing {
u32 clk_pre;
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c
new file mode 100644
index 0000000..197b039
--- /dev/null
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_28nm_8960.c
@@ -0,0 +1,195 @@
+/*
+ * Copyright (c) 2012-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "dsi_phy.h"
+#include "dsi.xml.h"
+
+static void dsi_28nm_dphy_set_timing(struct msm_dsi_phy *phy,
+ struct msm_dsi_dphy_timing *timing)
+{
+ void __iomem *base = phy->base;
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_0,
+ DSI_28nm_8960_PHY_TIMING_CTRL_0_CLK_ZERO(timing->clk_zero));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_1,
+ DSI_28nm_8960_PHY_TIMING_CTRL_1_CLK_TRAIL(timing->clk_trail));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_2,
+ DSI_28nm_8960_PHY_TIMING_CTRL_2_CLK_PREPARE(timing->clk_prepare));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_3, 0x0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_4,
+ DSI_28nm_8960_PHY_TIMING_CTRL_4_HS_EXIT(timing->hs_exit));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_5,
+ DSI_28nm_8960_PHY_TIMING_CTRL_5_HS_ZERO(timing->hs_zero));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_6,
+ DSI_28nm_8960_PHY_TIMING_CTRL_6_HS_PREPARE(timing->hs_prepare));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_7,
+ DSI_28nm_8960_PHY_TIMING_CTRL_7_HS_TRAIL(timing->hs_trail));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_8,
+ DSI_28nm_8960_PHY_TIMING_CTRL_8_HS_RQST(timing->hs_rqst));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_9,
+ DSI_28nm_8960_PHY_TIMING_CTRL_9_TA_GO(timing->ta_go) |
+ DSI_28nm_8960_PHY_TIMING_CTRL_9_TA_SURE(timing->ta_sure));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_10,
+ DSI_28nm_8960_PHY_TIMING_CTRL_10_TA_GET(timing->ta_get));
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_TIMING_CTRL_11,
+ DSI_28nm_8960_PHY_TIMING_CTRL_11_TRIG3_CMD(0));
+}
+
+static void dsi_28nm_phy_regulator_init(struct msm_dsi_phy *phy)
+{
+ void __iomem *base = phy->reg_base;
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_0, 0x3);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_1, 1);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_2, 1);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_3, 0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_4,
+ 0x100);
+}
+
+static void dsi_28nm_phy_regulator_ctrl(struct msm_dsi_phy *phy)
+{
+ void __iomem *base = phy->reg_base;
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_0, 0x3);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_1, 0xa);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_2, 0x4);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_3, 0x0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CTRL_4, 0x20);
+}
+
+static void dsi_28nm_phy_calibration(struct msm_dsi_phy *phy)
+{
+ void __iomem *base = phy->reg_base;
+ u32 status;
+ int i = 5000;
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_REGULATOR_CAL_PWR_CFG,
+ 0x3);
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_SW_CFG_2, 0x0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_CFG_1, 0x5a);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_CFG_3, 0x10);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_CFG_4, 0x1);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_CFG_0, 0x1);
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_TRIGGER, 0x1);
+ usleep_range(5000, 6000);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_MISC_CAL_HW_TRIGGER, 0x0);
+
+ do {
+ status = dsi_phy_read(base +
+ REG_DSI_28nm_8960_PHY_MISC_CAL_STATUS);
+
+ if (!(status & DSI_28nm_8960_PHY_MISC_CAL_STATUS_CAL_BUSY))
+ break;
+
+ udelay(1);
+ } while (--i > 0);
+}
+
+static void dsi_28nm_phy_lane_config(struct msm_dsi_phy *phy)
+{
+ void __iomem *base = phy->base;
+ int i;
+
+ for (i = 0; i < 4; i++) {
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_CFG_0(i), 0x80);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_CFG_1(i), 0x45);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_CFG_2(i), 0x00);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_TEST_DATAPATH(i),
+ 0x00);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_TEST_STR_0(i),
+ 0x01);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LN_TEST_STR_1(i),
+ 0x66);
+ }
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_CFG_0, 0x40);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_CFG_1, 0x67);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_CFG_2, 0x0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_TEST_DATAPATH, 0x0);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_TEST_STR0, 0x1);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LNCK_TEST_STR1, 0x88);
+}
+
+static int dsi_28nm_phy_enable(struct msm_dsi_phy *phy, int src_pll_id,
+ const unsigned long bit_rate, const unsigned long esc_rate)
+{
+ struct msm_dsi_dphy_timing *timing = &phy->timing;
+ void __iomem *base = phy->base;
+
+ DBG("");
+
+ if (msm_dsi_dphy_timing_calc(timing, bit_rate, esc_rate)) {
+ dev_err(&phy->pdev->dev,
+ "%s: D-PHY timing calculation failed\n", __func__);
+ return -EINVAL;
+ }
+
+ dsi_28nm_phy_regulator_init(phy);
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_LDO_CTRL, 0x04);
+
+ /* strength control */
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_STRENGTH_0, 0xff);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_STRENGTH_1, 0x00);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_STRENGTH_2, 0x06);
+
+ /* phy ctrl */
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_CTRL_0, 0x5f);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_CTRL_1, 0x00);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_CTRL_2, 0x00);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_CTRL_3, 0x10);
+
+ dsi_28nm_phy_regulator_ctrl(phy);
+
+ dsi_28nm_phy_calibration(phy);
+
+ dsi_28nm_phy_lane_config(phy);
+
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_BIST_CTRL_4, 0x0f);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_BIST_CTRL_1, 0x03);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_BIST_CTRL_0, 0x03);
+ dsi_phy_write(base + REG_DSI_28nm_8960_PHY_BIST_CTRL_4, 0x0);
+
+ dsi_28nm_dphy_set_timing(phy, timing);
+
+ return 0;
+}
+
+static void dsi_28nm_phy_disable(struct msm_dsi_phy *phy)
+{
+ dsi_phy_write(phy->base + REG_DSI_28nm_8960_PHY_CTRL_0, 0x0);
+
+ /*
+ * Wait for the registers writes to complete in order to
+ * ensure that the phy is completely disabled
+ */
+ wmb();
+}
+
+const struct msm_dsi_phy_cfg dsi_phy_28nm_8960_cfgs = {
+ .type = MSM_DSI_PHY_28NM_8960,
+ .src_pll_truthtable = { {true, true}, {false, true} },
+ .reg_cfg = {
+ .num = 1,
+ .regs = {
+ {"vddio", 1800000, 1800000, 100000, 100},
+ },
+ },
+ .ops = {
+ .enable = dsi_28nm_phy_enable,
+ .disable = dsi_28nm_phy_disable,
+ },
+};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
