From: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
IPQ5018 has tsens V1.0 IP with 4 sensors.
There is no RPM, so tsens has to be manually enabled. Adding the tsens
and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the
critical temperature being 120'C and action is to reboot. Adding all
the 4 zones here.
Signed-off-by: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
---
[v3] Ordered the qfprom device node properties as per
Krzysztof's comments
arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++
1 file changed, 169 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 9f13d2dcdfd5..9e28b54ebcbd 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -93,6 +93,117 @@ soc: soc@0 {
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
+ qfprom: qfprom@a0000 {
+ compatible = "qcom,ipq5018-qfprom", "qcom,qfprom";
+ reg = <0xa0000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tsens_base1: base1@249 {
+ reg = <0x249 2>;
+ bits = <3 8>;
+ };
+
+ tsens_base2: base2@24a {
+ reg = <0x24a 2>;
+ bits = <3 8>;
+ };
+
+ tsens_mode: mode@249 {
+ reg = <0x249 1>;
+ bits = <0 3>;
+ };
+
+ tsens_s0_p1: s0-p1@24b {
+ reg = <0x24b 0x2>;
+ bits = <2 6>;
+ };
+
+ tsens_s0_p2: s0-p2@24c {
+ reg = <0x24c 0x1>;
+ bits = <1 6>;
+ };
+
+ tsens_s1_p1: s1-p1@24c {
+ reg = <0x24c 0x2>;
+ bits = <7 6>;
+ };
+
+ tsens_s1_p2: s1-p2@24d {
+ reg = <0x24d 0x2>;
+ bits = <5 6>;
+ };
+
+ tsens_s2_p1: s2-p1@24e {
+ reg = <0x24e 0x2>;
+ bits = <3 6>;
+ };
+
+ tsens_s2_p2: s2-p2@24f {
+ reg = <0x24f 0x1>;
+ bits = <1 6>;
+ };
+
+ tsens_s3_p1: s3-p1@24f {
+ reg = <0x24f 0x2>;
+ bits = <7 6>;
+ };
+
+ tsens_s3_p2: s3-p2@250 {
+ reg = <0x250 0x2>;
+ bits = <5 6>;
+ };
+
+ tsens_s4_p1: s4-p1@251 {
+ reg = <0x251 0x2>;
+ bits = <3 6>;
+ };
+
+ tsens_s4_p2: s4-p2@254 {
+ reg = <0x254 0x1>;
+ bits = <0 6>;
+ };
+ };
+
+ tsens: thermal-sensor@4a9000 {
+ compatible = "qcom,ipq5018-tsens";
+ reg = <0x4a9000 0x1000>, /* TM */
+ <0x4a8000 0x1000>; /* SORT */
+
+ nvmem-cells = <&tsens_mode>,
+ <&tsens_base1>,
+ <&tsens_base2>,
+ <&tsens_s0_p1>,
+ <&tsens_s0_p2>,
+ <&tsens_s1_p1>,
+ <&tsens_s1_p2>,
+ <&tsens_s2_p1>,
+ <&tsens_s2_p2>,
+ <&tsens_s3_p1>,
+ <&tsens_s3_p2>,
+ <&tsens_s4_p1>,
+ <&tsens_s4_p2>;
+
+ nvmem-cell-names = "mode",
+ "base1",
+ "base2",
+ "s0_p1",
+ "s0_p2",
+ "s1_p1",
+ "s1_p2",
+ "s2_p1",
+ "s2_p2",
+ "s3_p1",
+ "s3_p2",
+ "s4_p1",
+ "s4_p2";
+
+ interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "uplow";
+ #qcom,sensors = <5>;
+ #thermal-sensor-cells = <1>;
+ };
+
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq5018-tlmm";
reg = <0x01000000 0x300000>;
@@ -240,6 +351,64 @@ frame@b128000 {
};
};
+ thermal-zones {
+ ubi32-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ ubi32-critical {
+ temperature = <120000>;
+ hysteresis = <2>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 2>;
+
+ trips {
+ cpu-critical {
+ temperature = <120000>;
+ hysteresis = <2>;
+ type = "critical";
+ };
+ };
+ };
+
+ top-glue-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ top_glue-critical {
+ temperature = <120000>;
+ hysteresis = <2>;
+ type = "critical";
+ };
+ };
+ };
+
+ gephy-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 4>;
+
+ trips {
+ gephy-critical {
+ temperature = <120000>;
+ hysteresis = <2>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
--
2.34.1
