Introduce binding documentation for the Qualcomm Shared Memory Point 2 Point
protocol.
Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx>
---
Changes since v1:
- No longer representing outgoing state as gpio-controller
.../devicetree/bindings/soc/qcom/qcom,smp2p.txt | 104 +++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
new file mode 100644
index 000000000000..5cc82b8353d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
@@ -0,0 +1,104 @@
+Qualcomm Shared Memory Point 2 Point binding
+
+The Shared Memory Point to Point (SMP2P) protocol facilitates communication of
+a single 32-bit value between two processors. Each value has a single writer
+(the local side) and a single reader (the remote side). Values are uniquely
+identified in the system by the directed edge (local processor ID to remote
+processor ID) and a string identifier.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,smp2p"
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: one entry specifying the smp2p notification interrupt
+
+- qcom,ipc:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: three entries specifying the outgoing ipc bit used for
+ signaling the remote end of the smp2p edge:
+ - phandle to a syscon node representing the apcs registers
+ - u32 representing offset to the register within the syscon
+ - u32 representing the ipc bit within the register
+
+- qcom,smem:
+ Usage: required
+ Value type: <u32 array>
+ Definition: two identifiers of the inbound and outbound smem items used
+ for this edge
+
+- qcom,local-pid:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the identfier of the local endpoint of this edge
+
+- qcom,remote-pid:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the identfier of the remote endpoint of this edge
+
+= SUBNODES
+Each SMP2P pair contain a set of inbound and outbound entries, these are
+described in subnodes of the smp2p device node. The node names are not
+important.
+
+- qcom,entry-name:
+ Usage: required
+ Value type: <string>
+ Definition: specifies the name of this entry, for inbound entries this
+ will be used to match against the remotely allocated entry
+ and for outbound entries this name is used for allocating
+ entries
+
+- interrupt-controller:
+ Usage: required for incoming entries
+ Value type: <empty>
+ Definition: marks the entry as inbound; the node should be specified
+ as a two cell interrupt-controller as defined in
+ "../interrupt-controller/interrupts.txt"
+ If not specified this node will denote the outgoing entry
+
+- #interrupt-cells:
+ Usage: required for incoming entries
+ Value type: <u32>
+ Definition: must be 2 - denoting the bit in the entry and IRQ flags
+
+- #qcom,state-cells:
+ Usage: required for outgoing entries
+ Value type: <u32>
+ Definition: must be 1 - denoting the bit in the entry
+
+= EXAMPLE
+The following example shows the SMP2P setup with the wireless processor,
+defined from the 8974 apps processor's point-of-view. It encompasses one
+inbound and one outbound entry:
+
+wcnss-smp2p {
+ compatible = "qcom,smp2p";
+ qcom,smem = <431>, <451>;
+
+ interrupts = <0 143 1>;
+
+ qcom,ipc = <&apcs 8 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ wcnss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,state-cells = <1>;
+ };
+
+ wcnss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
