[PATCH 1/6] scsi: ufs: ufs-qcom: Setup host power mode during init

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.

Co-developed-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
Signed-off-by: Can Guo <quic_cang@xxxxxxxxxxx>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@xxxxxxxxxxx>
---
 drivers/ufs/host/ufs-qcom.c | 27 ++++++++++++++++++---------
 drivers/ufs/host/ufs-qcom.h |  1 +
 2 files changed, 19 insertions(+), 9 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index c3215d3..710f079 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -443,7 +443,11 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
 static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+	struct ufs_dev_params *host_pwr_cap = &host->host_pwr_cap;
 	struct phy *phy = host->generic_phy;
+	enum phy_mode mode = host_pwr_cap->hs_rate == PA_HS_MODE_B ?
+							PHY_MODE_UFS_HS_B :
+							PHY_MODE_UFS_HS_A;
 	int ret;
 
 	/* Reset UFS Host Controller and PHY */
@@ -460,7 +464,7 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
 		return ret;
 	}
 
-	phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);
+	phy_set_mode_ext(phy, mode, host->phy_gear);
 
 	/* power on phy - start serdes and phy's power and clocks */
 	ret = phy_power_on(phy);
@@ -884,7 +888,6 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 				struct ufs_pa_layer_attr *dev_req_params)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
-	struct ufs_dev_params ufs_qcom_cap;
 	int ret = 0;
 
 	if (!dev_req_params) {
@@ -894,13 +897,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 
 	switch (status) {
 	case PRE_CHANGE:
-		ufshcd_init_pwr_dev_param(&ufs_qcom_cap);
-		ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
-
-		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
-		ufs_qcom_cap.hs_tx_gear = ufs_qcom_cap.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
-
-		ret = ufshcd_get_pwr_dev_param(&ufs_qcom_cap,
+		ret = ufshcd_get_pwr_dev_param(&host->host_pwr_cap,
 					       dev_max_params,
 					       dev_req_params);
 		if (ret) {
@@ -1037,6 +1034,17 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
 		hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
 }
 
+static void ufs_qcom_set_pwr_mode_limits(struct ufs_hba *hba)
+{
+	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+	struct ufs_dev_params *host_pwr_cap = &host->host_pwr_cap;
+
+	ufshcd_init_pwr_dev_param(host_pwr_cap);
+
+	/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
+	host_pwr_cap->hs_tx_gear = host_pwr_cap->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
+}
+
 static void ufs_qcom_set_caps(struct ufs_hba *hba)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1259,6 +1267,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
 	if (err)
 		goto out_variant_clear;
 
+	ufs_qcom_set_pwr_mode_limits(hba);
 	ufs_qcom_set_caps(hba);
 	ufs_qcom_advertise_quirks(hba);
 
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index fa54248..4db64d9 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -227,6 +227,7 @@ struct ufs_qcom_host {
 
 	struct gpio_desc *device_reset;
 
+	struct ufs_dev_params host_pwr_cap;
 	u32 phy_gear;
 
 	bool esi_enabled;
-- 
2.7.4




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux