On 9/8/2023 10:53 PM, Manivannan Sadhasivam wrote:
The "hs_gear" variable is used to program the PHY settings (submode) during
ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
agreed gear changes. Due to this, if the gear got downscaled before suspend
(runtime/system), then while resuming, the PHY settings for the lower gear
will be applied first and later when scaling to max gear with REINIT, the
PHY settings for the max gear will be applied.
This adds a latency while resuming and also really not needed as the PHY
gear settings are backwards compatible i.e., we can continue using the PHY
settings for max gear with lower gear speed.
So let's update the "hs_gear" variable _only_ when the agreed gear is
greater than the current one. This guarantees that the PHY settings will be
changed only during probe time and fatal error condition.
Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
when the PM operation is in progress.
Cc: stable@xxxxxxxxxxxxxxx
Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Reported-by: Can Guo <quic_cang@xxxxxxxxxxx>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
---
drivers/ufs/core/ufshcd.c | 3 ++-
drivers/ufs/host/ufs-qcom.c | 9 +++++++--
2 files changed, 9 insertions(+), 3 deletions(-)
diff --git a/drivers/ufs/core/ufshcd.c b/drivers/ufs/core/ufshcd.c
index 34472871610d..1f0a9d96e613 100644
--- a/drivers/ufs/core/ufshcd.c
+++ b/drivers/ufs/core/ufshcd.c
@@ -8782,7 +8782,8 @@ static int ufshcd_probe_hba(struct ufs_hba *hba, bool init_dev_params)
if (ret)
goto out;
- if (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH) {
+ if (!hba->pm_op_in_progress &&
+ (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH)) {
/* Reset the device and controller before doing reinit */
ufshcd_device_reset(hba);
ufshcd_hba_stop(hba);
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 78689d3479e4..ebb8054a3b3e 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -909,8 +909,13 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
return ret;
}
- /* Use the agreed gear */
- host->hs_gear = dev_req_params->gear_tx;
+ /*
+ * Update hs_gear only when the gears are scaled to a higher value. This is because,
+ * the PHY gear settings are backwards compatible and we only need to change the PHY
+ * settings while scaling to higher gears.
+ */
+ if (dev_req_params->gear_tx > host->hs_gear)
+ host->hs_gear = dev_req_params->gear_tx;
/* enable the device ref clock before changing to HS mode */
if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
Reviewed-by: Can Guo <quic_cang@xxxxxxxxxxx>
Tested-by: Can Guo <quic_cang@xxxxxxxxxxx>
