[PATCH RESEND 0/7] Add GPLL0 as clock provider for the Qualcomm's IPQ mailbox controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently mailbox controller takes the XO and APSS PLL as the input. It
can take the GPLL0 also as an input. This patch series adds the same and
fixes the issue caused by this.

Once the cpufreq driver is up, it tries to bump up the cpu frequency
above 800MHz, while doing so system is going to unusable state. Reason
being, with the GPLL0 included as clock source, clock framework tries to
achieve the required rate with the possible parent and since GPLL0 carries
the CLK_SET_RATE_PARENT flag, clock rate of the GPLL0 is getting
changed, causing the issue.

First half of the series, removes the CLK_SET_RATE_PARENT flag from the
PLL clocks since the PLL clock rates shouldn't be changed. Another
half, add the necessary support to include the GPLL0 as clock provider
for mailbox and accomodate the changes in APSS clock driver.

This is also the preparatory series to enable the CPUFreq on IPQ5332
SoC. Dynamic scaling of CPUFreq is not supported on IPQ5332, so to
switch between the frequencies we need to park the APSS PLL in safe
source, here it is GPLL0 and then shutdown and bring up the APSS PLL in
the desired rate.

For IPQ5332 SoC, this series depends on the below patch
https://lore.kernel.org/linux-arm-msm/1693474133-10467-1-git-send-email-quic_varada@xxxxxxxxxxx/

Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx>
---
Kathiravan Thirumoorthy (7):
      clk: qcom: ipq8074: drop the CLK_SET_RATE_PARENT flag from PLL clocks
      clk: qcom: ipq6018: drop the CLK_SET_RATE_PARENT flag from PLL clocks
      clk: qcom: ipq9574: drop the CLK_SET_RATE_PARENT flag from GPLL clocks
      clk: qcom: ipq5332: drop the CLK_SET_RATE_PARENT flag from GPLL clocks
      dt-bindings: mailbox: qcom: add one more clock provider for IPQ mailbox
      clk: qcom: apss-ipq6018: add the GPLL0 clock also as clock provider
      arm64: dts: qcom: include the GPLL0 as clock provider for IPQ mailbox

 .../devicetree/bindings/mailbox/qcom,apcs-kpss-global.yaml         | 2 ++
 arch/arm64/boot/dts/qcom/ipq5332.dtsi                              | 4 ++--
 arch/arm64/boot/dts/qcom/ipq6018.dtsi                              | 4 ++--
 arch/arm64/boot/dts/qcom/ipq8074.dtsi                              | 4 ++--
 arch/arm64/boot/dts/qcom/ipq9574.dtsi                              | 4 ++--
 drivers/clk/qcom/apss-ipq6018.c                                    | 3 +++
 drivers/clk/qcom/gcc-ipq5332.c                                     | 2 --
 drivers/clk/qcom/gcc-ipq6018.c                                     | 7 -------
 drivers/clk/qcom/gcc-ipq8074.c                                     | 7 -------
 drivers/clk/qcom/gcc-ipq9574.c                                     | 4 ----
 10 files changed, 13 insertions(+), 28 deletions(-)
---
base-commit: a47fc304d2b678db1a5d760a7d644dac9b067752
change-id: 20230904-gpll_cleanup-8b3e8b058c8b

Best regards,
-- 
Kathiravan Thirumoorthy <quic_kathirav@xxxxxxxxxxx>




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux