Re: [PATCH v2] arm64: dts: ipq5018: Correct uart1_pins pinconf

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 31/08/2023 17:34, Ziyang Huang wrote:
In pinctrl, the pinconfigs for uart are named "blspX_uartY".
   X is the UART ID. Starts from 1.
     1-6 are in BLSP Block 1.
     7-12 are in BLSP Block 2.
   Y is the index of mux config. Starts from 0.

In dts, the serials are also named "blspX_uartY", but with different logic.
   X is the BLSP Block ID. Starts from 1.
   Y is the uart id inside block.
     In "ipq6018.dtsi" and "ipq8074.dtsi", it starts from 1.
     But in "ipq5332.dtsi" and "ipq9574.dtsi", it starts from 0.

+-----------------+-----------------+-------------+-----------------+
|     Block ID    | ID inside Block |  dts name   | pinconfig name  |
| (Starts from 1) | (Starts from 1) |             |                 |
+-----------------+-----------------+-------------+-----------------+
|        1        |        1        | blsp1_uart1 |   blsp0_uartY   |
|        1        |        2        | blsp1_uart2 |   blsp1_uartY   |
|        1        |        6        | blsp1_uart6 |   blsp5_uartY   |
|        2        |        1        | blsp2_uart1 |   blsp6_uartY   |
|        2        |        6        | blsp2_uart6 |   blsp12_uartY  |
+-----------------+-----------------+-------------+-----------------+

In "ipq5018.dts", "blsp1_uart1" (dts name) is the first serial (confimed
by the address), So its pinconfig should be "blsp0_uart0" (pinconfig name,
use GPIO 20 and 21) or "blsp0_uart1" (pinconfig name, use GPIO 28 and 29).

Fixes: 570006756a16 ("arm64: dts: Add ipq5018 SoC and rdp432-c2 board support")
Signed-off-by: Ziyang Huang <hzyitc@xxxxxxxxxxx>
---
Changes since v1
- Use corrent name in From

  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 6 +++---
  1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 9f13d2dcdfd5..91b98020e1c6 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -104,10 +104,10 @@ tlmm: pinctrl@1000000 {
  			#interrupt-cells = <2>;
uart1_pins: uart1-state {
-				pins = "gpio31", "gpio32", "gpio33", "gpio34";
-				function = "blsp1_uart1";
+				pins = "gpio28", "gpio29";
+				function = "blsp0_uart1";
  				drive-strength = <8>;
-				bias-pull-down;
+				bias-disabled;
  			};
  		};

So this change will have the effect of changing the console on ipq5018-rdp432 from gpio31-gpio34 to gpio28, gpio29.

Have you verified that change on hardware or the schematic ?

https://forum.openwrt.org/t/add-support-for-xiaomi-redmi-ax5400-white-version/140879/22?page=2

This has the wrong UART pinout ?

Is this change something that should be expressed for a particular board ?

---
bod



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux