Re: [PATCH v3 2/4] firmware: qcom_scm: disable SDI if required

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 8/16/2023 10:15 PM, Robert Marko wrote:
IPQ5018 has SDI (Secure Debug Image) enabled by TZ by default, and that
means that WDT being asserted or just trying to reboot will hang the board
in the debug mode and only pulling the power and repowering will help.
Some IPQ4019 boards like Google WiFI have it enabled as well.

Luckily, SDI can be disabled via an SCM call.

So, lets use the boolean DT property to identify boards that have SDI
enabled by default and use the SCM call to disable SDI during SCM probe.
It is important to disable it as soon as possible as we might have a WDT
assertion at any time which would then leave the board in debug mode,
thus disabling it during SCM removal is not enough.

Signed-off-by: Robert Marko <robimarko@xxxxxxxxx>
---
Changes in v3:
* Squashed ("firmware: qcom: scm: Add SDI disable support") and
("firmware: qcom_scm: disable SDI if required")
---
  drivers/firmware/qcom_scm.c | 29 +++++++++++++++++++++++++++++
  drivers/firmware/qcom_scm.h |  1 +
  2 files changed, 30 insertions(+)

diff --git a/drivers/firmware/qcom_scm.c b/drivers/firmware/qcom_scm.c
index 06fe8aca870d..de9d1a11d097 100644
--- a/drivers/firmware/qcom_scm.c
+++ b/drivers/firmware/qcom_scm.c
@@ -403,6 +403,29 @@ int qcom_scm_set_remote_state(u32 state, u32 id)
  }
  EXPORT_SYMBOL_GPL(qcom_scm_set_remote_state);
+static int qcom_scm_disable_sdi(void)
+{
+	int ret;
+	struct qcom_scm_desc desc = {
+		.svc = QCOM_SCM_SVC_BOOT,
+		.cmd = QCOM_SCM_BOOT_SDI_CONFIG,
+		.args[0] = 1, /* Disable watchdog debug */
+		.args[1] = 0, /* Disable SDI */
+		.arginfo = QCOM_SCM_ARGS(2),
+		.owner = ARM_SMCCC_OWNER_SIP,
+	};
+	struct qcom_scm_res res;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+	ret = qcom_scm_call(__scm->dev, &desc, &res);

Would you not be wanting this call to be atomic ?

+
+	qcom_scm_clk_disable();
+
+	return ret ? : res.result[0];
+}
+
  static int __qcom_scm_set_dload_mode(struct device *dev, bool enable)
  {
  	struct qcom_scm_desc desc = {
@@ -1468,6 +1491,12 @@ static int qcom_scm_probe(struct platform_device *pdev)
  	if (download_mode)
  		qcom_scm_set_download_mode(true);
+ /*
+	 * Disable SDI if indicated by DT that it is enabled by default.
+	 */
+	if (of_property_read_bool(pdev->dev.of_node, "qcom,sdi-enabled"))
+		qcom_scm_disable_sdi();

Why don't we do this call in qcom_scm_shutdown()
also does it not conflict with above download_mode
we have enabled download mode but disabling SDI
means (hard reset) and will not be collecting
crash dump?

-Mukesh

+
  	return 0;
  }
diff --git a/drivers/firmware/qcom_scm.h b/drivers/firmware/qcom_scm.h
index e6e512bd57d1..7b68fa820495 100644
--- a/drivers/firmware/qcom_scm.h
+++ b/drivers/firmware/qcom_scm.h
@@ -80,6 +80,7 @@ extern int scm_legacy_call(struct device *dev, const struct qcom_scm_desc *desc,
  #define QCOM_SCM_SVC_BOOT		0x01
  #define QCOM_SCM_BOOT_SET_ADDR		0x01
  #define QCOM_SCM_BOOT_TERMINATE_PC	0x02
+#define QCOM_SCM_BOOT_SDI_CONFIG	0x09
  #define QCOM_SCM_BOOT_SET_DLOAD_MODE	0x10
  #define QCOM_SCM_BOOT_SET_ADDR_MC	0x11
  #define QCOM_SCM_BOOT_SET_REMOTE_STATE	0x0a



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux