On Tue, 11 Jul 2023 at 14:41, Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> wrote:
>
> On 11.07.2023 12:56, Dmitry Baryshkov wrote:
> > On Tue, 11 Jul 2023 at 13:48, Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> wrote:
> >>
> >> On 11.07.2023 12:44, Dmitry Baryshkov wrote:
> >>> On Tue, 11 Jul 2023 at 13:28, Konrad Dybcio <konrad.dybcio@xxxxxxxxxx> wrote:
> >>>>
> >>>> Add and assign RPM regulators coming from PM2250.
> >>>>
> >>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> >>>> ---
> >> [...]
> >>
> >>>> + pm2250_l5: l5 {
> >>>> + /* CSI/DSI */
> >>>> + regulator-min-microvolts = <1232000>;
> >>>> + regulator-max-microvolts = <1232000>;
> >>>> + regulator-allow-set-load;
> >>>> + regulator-boot-on;
> >>>
> >>> why?
> >>>
> >> To answer all of the questions in one go:
> >>
> >> "it's because the regulator is enabled at boot"
> >
> > I was more concerned about the following part:
> > If the bootloader didn't leave it on then OS should turn it on at boot ...
> >
> > Please remind me, are we declaring them as boot-on so that the
> > regulator core can turn them off later if they are unused?
> In the Linux implementation, yes.
Ack.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
>
> Konrad
> >
> >>
> >> Konrad
> >>>> + };
> >>>> +
> >>>> + pm2250_l6: l6 {
> >>>> + /* DRAM PLL */
> >>>> + regulator-min-microvolts = <928000>;
> >>>> + regulator-max-microvolts = <928000>;
> >>>> + regulator-always-on;
> >>>> + regulator-boot-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l7: l7 {
> >>>> + /* Wi-Fi CX/MX */
> >>>> + regulator-min-microvolts = <664000>;
> >>>> + regulator-max-microvolts = <664000>;
> >>>> + };
> >>>> +
> >>>> + /*
> >>>> + * L8 - VDD_LPI_CX
> >>>> + * L9 - VDD_LPI_MX
> >>>> + */
> >>>> +
> >>>> + pm2250_l10: l10 {
> >>>> + /* Wi-Fi RFA */
> >>>> + regulator-min-microvolts = <1300000>;
> >>>> + regulator-max-microvolts = <1300000>;
> >>>> + };
> >>>> +
> >>>> + pm2250_l11: l11 {
> >>>> + /* GPS RF1 */
> >>>> + regulator-min-microvolts = <1000000>;
> >>>> + regulator-max-microvolts = <1000000>;
> >>>> + regulator-boot-on;
> >>>
> >>> Shouldn't it be handled by the modem on its own?
> >>>
> >>>> + };
> >>>> +
> >>>> + pm2250_l12: l12 {
> >>>> + /* USB PHYs */
> >>>> + regulator-min-microvolts = <928000>;
> >>>> + regulator-max-microvolts = <928000>;
> >>>> + regulator-allow-set-load;
> >>>> + regulator-boot-on;
> >>>
> >>> You guess the question (and further on)
> >>>
> >>>> + };
> >>>> +
> >>>> + pm2250_l13: l13 {
> >>>> + /* USB/QFPROM/PLLs */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + regulator-allow-set-load;
> >>>> + regulator-boot-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l14: l14 {
> >>>> + /* SDHCI1 VQMMC */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + regulator-allow-set-load;
> >>>> + /* Broken hardware, never turn it off! */
> >>>> + regulator-always-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l15: l15 {
> >>>> + /* WCD/DSI/BT VDDIO */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + regulator-allow-set-load;
> >>>> + regulator-always-on;
> >>>> + regulator-boot-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l16: l16 {
> >>>> + /* GPS RF2 */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + regulator-boot-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l17: l17 {
> >>>> + regulator-min-microvolts = <3000000>;
> >>>> + regulator-max-microvolts = <3000000>;
> >>>> + };
> >>>> +
> >>>> + pm2250_l18: l18 {
> >>>> + /* VDD_PXn */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + };
> >>>> +
> >>>> + pm2250_l19: l19 {
> >>>> + /* VDD_PXn */
> >>>> + regulator-min-microvolts = <1800000>;
> >>>> + regulator-max-microvolts = <1800000>;
> >>>> + };
> >>>> +
> >>>> + pm2250_l20: l20 {
> >>>> + /* SDHCI1 VMMC */
> >>>> + regulator-min-microvolts = <2856000>;
> >>>> + regulator-max-microvolts = <2856000>;
> >>>> + regulator-allow-set-load;
> >>>> + };
> >>>> +
> >>>> + pm2250_l21: l21 {
> >>>> + /* SDHCI2 VMMC */
> >>>> + regulator-min-microvolts = <2960000>;
> >>>> + regulator-max-microvolts = <3300000>;
> >>>> + regulator-allow-set-load;
> >>>> + regulator-boot-on;
> >>>> + };
> >>>> +
> >>>> + pm2250_l22: l22 {
> >>>> + /* Wi-Fi */
> >>>> + regulator-min-microvolts = <3312000>;
> >>>> + regulator-max-microvolts = <3312000>;
> >>>> + };
> >>>> + };
> >>>> +};
> >>>> +
> >>>> &sdhc_1 {
> >>>> + vmmc-supply = <&pm2250_l20>;
> >>>> + vqmmc-supply = <&pm2250_l14>;
> >>>> pinctrl-0 = <&sdc1_state_on>;
> >>>> pinctrl-1 = <&sdc1_state_off>;
> >>>> pinctrl-names = "default", "sleep";
> >>>> @@ -61,6 +322,8 @@ &sdhc_1 {
> >>>> };
> >>>>
> >>>> &sdhc_2 {
> >>>> + vmmc-supply = <&pm2250_l21>;
> >>>> + vqmmc-supply = <&pm2250_l4>;
> >>>> cd-gpios = <&tlmm 88 GPIO_ACTIVE_LOW>;
> >>>> pinctrl-0 = <&sdc2_state_on &sd_det_in_on>;
> >>>> pinctrl-1 = <&sdc2_state_off &sd_det_in_off>;
> >>>> @@ -104,6 +367,9 @@ &usb {
> >>>> };
> >>>>
> >>>> &usb_hsphy {
> >>>> + vdd-supply = <&pm2250_l12>;
> >>>> + vdda-pll-supply = <&pm2250_l13>;
> >>>> + vdda-phy-dpdm-supply = <&pm2250_l21>;
> >>>> status = "okay";
> >>>> };
> >>>>
> >>>>
> >>>> ---
> >>>> base-commit: 8e4b7f2f3d6071665b1dfd70786229c8a5d6c256
> >>>> change-id: 20230711-topic-rb1_regulator-44c4ade93246
> >>>>
> >>>> Best regards,
> >>>> --
> >>>> Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> >>>>
> >>>
> >>>
> >
> >
> >
--
With best wishes
Dmitry
