On Fri, Jun 30, 2023 at 04:22:09PM +0530, Krishna chaitanya chundru wrote:
Subject prefix should be "PCI: qcom-ep:"
> Add wakeup host op to dw_pcie_ep_ops to wake up host.
> If the EPF asks to send PME trigger the inband PME by writing
> into the parf registers otherwise toggle wake signal.
>
If the wakeup type is PME, then trigger inband PME by writing to the PARF
PARF_PM_CTRL register, otherwise toggle #WAKE.
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> ---
> drivers/pci/controller/dwc/pcie-qcom-ep.c | 31 +++++++++++++++++++++++++++++++
> 1 file changed, 31 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> index e75aec4..e382b4b 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> @@ -89,6 +89,7 @@
> /* PARF_PM_CTRL register fields */
> #define PARF_PM_CTRL_REQ_EXIT_L1 BIT(1)
> #define PARF_PM_CTRL_READY_ENTR_L23 BIT(2)
> +#define PARF_PM_CTRL_XMT_PME BIT(4)
> #define PARF_PM_CTRL_REQ_NOT_ENTR_L1 BIT(5)
>
> /* PARF_MHI_CLOCK_RESET_CTRL fields */
> @@ -729,10 +730,40 @@ static void qcom_pcie_ep_init(struct dw_pcie_ep *ep)
> dw_pcie_ep_reset_bar(pci, bar);
> }
>
> +static int qcom_pcie_ep_wakeup_host(struct dw_pcie_ep *ep, u8 func_no,
> + enum pci_epc_wakeup_host_type type)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
> + struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
> + struct device *dev = pci->dev;
> + u32 val;
> +
> + if (type == PCI_WAKEUP_TOGGLE_WAKE) {
> + dev_dbg(dev, "Waking up the host by toggling WAKE#\n");
> + gpiod_set_value_cansleep(pcie_ep->wake, 1);
> + usleep_range(WAKE_DELAY_US, WAKE_DELAY_US + 500);
> + gpiod_set_value_cansleep(pcie_ep->wake, 0);
> + return 0;
> +
> + } else if (type == PCI_WAKEUP_SEND_PME) {
> + dev_dbg(dev, "Waking up the host using PME\n");
> + val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> + val |= PARF_PM_CTRL_XMT_PME;
> + writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
> +
> + } else {
> + dev_err(dev, "Device is not in D3 state wakeup is not supported\n");
> + return -EOPNOTSUPP;
This is not needed if you use bool. And this debug message is wrong btw since
you are not checking whether the device is in D3 state or not.
- Mani
> + }
> +
> + return 0;
> +}
> +
> static const struct dw_pcie_ep_ops pci_ep_ops = {
> .ep_init = qcom_pcie_ep_init,
> .raise_irq = qcom_pcie_ep_raise_irq,
> .get_features = qcom_pcie_epc_get_features,
> + .wakeup_host = qcom_pcie_ep_wakeup_host,
> };
>
> static int qcom_pcie_ep_probe(struct platform_device *pdev)
> --
> 2.7.4
>
--
மணிவண்ணன் சதாசிவம்
